background image

 

 

   

  

 

 

18(20) 

 

 

 

© Soneco Oy.

  

 

V 23.7.2013 

 

Staus: Contents schecked 

Author: JR 

Annex A: Tone and light indications of CC3 

A1. When the device is OFF (OFF mode) 

The  OFF  is  nt  indicated.  Upon  pressing  the  button,  the  device  gives  and  audible 
signal and the YELLOW light is on.  

If there is no indication from the button, the battery is empty and needs charging. 

A2. OFF mode with connected charger 

The connection of the charger causes an audible tone and the YELLOW light is on 
with  the  brightness  according  to  the  voltage.  The  beginning  of  charging  will  be 
indicated with three tones and bright YELLOW flashes. After this, the progress of the 
charging will be shown with YELLOW light:  

In the case of deep discharge, connecting the charger causes no tone. The stages 
of pre-charging will be indicated as follows: 
-  

YELLOW flash once on 4 seconds: Pre-charging makes progress. 

-  

YELLOW two flashes in 4 seconds: Slow charging started. 

-  

YELLOW three flashes in 4 seconds: Slow Charging nearly completed.  

-  

YELLOW ON/OFF in 2 seconds: Fast charging being started.  

YELLOW on and bright: Fast charging, nearly empty battery, strong charging  

YELLOW dimmed = nearly full battery 

No light: Battery full. 

Two  audible  tones  and  YELLOW  flashes.  Charging  completed  and  battery  full. 
Continuous  RED  when  the  charger  connected  or  during  charging:  Over  voltage  of 
the charger or battery. Faulty or wrong charger, or a faulty battery  

A3. During start-up 

Upon pressing the button for over 5 seconds the YELLOW starts to blink. Releasing 
the  button  initiates  the  start-up  of  the  device.  YELLOW  continues  to  blink  in  ca.  1 
second intervals. 

Three  tones  and  RED  flashes  in  an  early  stage  of  start-up  indicate  a  SIM  error, 
missing SIM, PIN-error or missing PIN. The start-up continues. After a new SIM/PIN-
error indication the device enters the LIMITED mode.  

RED starts to blink frequently: LIMITED mode. 

It is not possible to interrupt the start-up.  

During start-up there is no indication about charging. After the start-up the status of 
charging will be indicated again.  

A4. In standby mode 

At  the  beginning  of  ready  state  GREEN  is  on  for  5  seconds  if  the  entering  the 
programming mode by pressing the button is allowed.   

GREEN blinks every 2 seconds: standby mode OK. 

RED blinks: Network connection lost for the time being, recovery efforts ongoing. 

RED Blinks and tones: SIM error. The device will be switched off and re-started.  

GREEN, YELLOW and RED blink alternating with a melodic ringing tone. Incoming 
call. Note that the call may be set as silent.   

Summary of Contents for CC3





















Reviews: