background image

Section 3

Technical specifications

Coder / Decoder Mode

ADA102 is able to work as Coder or Decoder by software configuration.

Full-duplex 

supported for non compressed audio streaming. 

Analog Input / Output

Stereo balanced In / Outs -10 to + 15 dBu input level, regulated by front panel level control
Max output level + 20 dBm over 600 ohms (at FSD level)  0 VU at meter: + 4 dBu out

Digital IN / Out

AES 3 professional balanced digital stereo IN / Out Z=110 Ohms.
Full compatible S/PDIF

Frequency Response

Analog: 30 - 15.000 Hz +/- 0,5 dB @ 192 kbps
Digital AES-3: 20 - 15.000 Hz +/- 0,1 dB @ 192 kbps 

Distortion

Less than 0,01 % THD distortion, Analog or Digital @ 192 kbps
Typical AES-3: 0,005 % @ 192 kbps Total Decoder

Noise

Dynamic Range > 70 dBA @ 192 kbps as encoder
Dynamic Range > 80 dBA @ 192 kbps as decoder
Dynamic range AES 3: > 90 dBA @ 192, Total E Decoder

 

Headroom

Safety level from 0 VU meter to Full Digital Scale: 15 dB

VUmeter Level

Measures true peak level with a peak-hold system

Channel Separation

Better than 70 dB @ 1 kHz, Analog
Better than 90 dB @ 1 kHz, Digital AES 3

Power supply

220-240V / 110 - 127 V 50 / 60 Hz, 15 VA

Digital Streaming Input / Output 

Streaming connection

Standard RJ45 Ethernet connection TCP/IP

Standards supported

• MP3 Layer 1 (32, 44.1 and 48 kHz)
• MP3 Layer 2 (16, 22.05 and 24 kHz)
• G.711 (µLaw / A-Law 8 and 24 kHz sampling rate)
• 16bit PCM uncompressed (from 8 KHz to 48 KHz)

MONO Streaming:  

MPEG1/2 Layer 3, VBR (Fs:48KHz): 72 76 80 88 96 112 144 160kbps

STEREO Streaming

:  MPEG1/2 Layer 3, VBR (Fs:48KHz): 88 96 104 120 144 160 176 192kbps

Protocols

IP standard based protocols; TCP/IP, UDP, HTTP, ICMP, SNMP
Supports BootP, DHCP and Auto IP. 
Supports 

RTP

 for low latency audio streaming.

Latency 

(time delay)

ADA102 has a latency of only 20 mS (uncompressed audio) on LAN 

Variable Bit Rate 

(VBR)

Encoding

The encoder uses Variable Bitrate Encoding (VBR) to realize optimal compression of the audio 
data. The setting of a fixed bitrate is replaced with setting a quality level that preserves audio 
quality in critical sections and enhances compression otherwise.

SOLIDYNE

ADA102 CODER/DECODER

Page 19

Summary of Contents for ADA102





















Reviews: