Solidyne ADA102 Owner'S Manual Download Page 13

Page: 13 / 20

2.2

Advanced settings

2.2.1 Setting temporary IP address

using ARP command

This procedure is used to temporarily set the IP address
for first time browser access to the ADA102, in the case
where you have no LAN and wants to access from a
Notebook.

After this procedure the temporary IP will be active only
as long as the ADA102 stays powered. After a restart
the procedure has to be repeated unless you have
configure it with a static IP address.

Step 1

Use  either a  “crossover”  network  cable  between  the
ADA102  and  the   PC   or   use   two   network   cables   to
connect the  ADA102  and the PC to a network switch

and power the ADA102.

Make sure that you have a valid IP address configured on your

PC (e.g. 192.168.0.2).

Step 2

Open a command window. Windows: click on “Start”,
click on “Run..”, in the “Open” field type

cmd

, click on

“OK”.

OSX / Linux: Open a terminal window

Step 3

Please proceed to step 4 if you used a “crossover” network

cable in the preparation step above.
To ensure that we use a free IP address (not already used by

another device in the network) we have to use the Ping

command. In this example we assume the PC to have the IP

address “192.168.0.2” and want to check if “192.168.0.6” is

free.

To do so type

ping 192.168.0.6

and hit the “Enter” key.

If you get a reply (IP already used) then try to ping
another IP until you find one that is not used. If the
request times out (no reply) then the “pinged” IP is free
and we can continue with the next step.

Step 4

Look for the Solidyne ADA102 MAC address printed on
a label placed on the rear panel (12 hex digits,
separated by a hyphen every 2 digits). Type into the
windows command window:

arp -s 192.168.0.6 00-08-E1-00-B1-77

and hit the “Enter” key (replace the digits according to
your devices MAC address). On a OSX or Linux system
type into the terminal:

arp -s 192.168.0.6 00:08:E1:00:B1:77

Step 5

Now we have to make the ADA102 listen to the IP
address “192.168.0.6” using the Telnet command.

To do so type into the command window:

telnet 192.168.0.6 1

and hit the “Enter” key

(the number “one” must be there for this command to
work correctly !!!).

The ADA102 will refuse the

connection on port

immediately but will be available

for web access on the

IP address used as long as the

device stays powered.

Step 6

To check if the ADA102 is responding you can use the ping

command again. To do so type:

ping 192.168.0.6

and hit the “Enter” key.

If you do get a reply the IP address 192.168.0.6 can be used

to access the ADA102 using a web browser. If you do get

“request timed out” then please repeat step 6 carefully (you

most likely mistyped the telnet command) or repeat the

entire procedure.

2.2.2 Static IP

You can define a static IP. The advantage is that a
known IP allows you to access to the web panel, in case
that you requires change settings; without the necessity
of listen the audio to know the IP (voice IP announced
on start up).

By default the IP address is set to 0.0.0.0 (Dynamic IP
disabled). To change it, go to “Configuration →
Network”.

Use SonicIP:

If set to "yes", the device will announce

its IP address over the audio output. Default: "yes".

IP Address:

Enter the IP address of the device, e.g.:

"0.0.0.0" for automatic discovery (DHCP/Bootp, IPzator,
AutoIP) "192.168.0.12" for an internal LAN. Default:
"0.0.0.0"

Netmask:

Enter the 4 values of the desired Static IP

e.g.: "0.0.0.0" for a default Netmask depending on the
used IP Address. "255.255.255.0" for a C class network
Default: "255.255.255.0".

Gateway IP Address:

Enter the IP address of the