background image

7

MODULYS Green Power 

- Ref.: IOMMODGPXX01-GB  00

ENGLISH

2. REQUISITES

Electrical requisites.

2.2. 

The installation and the system must comply with national plant regulations. The electrical distribution panel must have a protection 
and sectioning system installed for the input mains and the auxiliary mains.

The table below show the size of the input protection devices recommended for correct installation.

Power 

module

Input 

voltage

Output 

voltage

Input 

breaker 

(1)

Differential 

Input

(2)

Input 

cable

Aux mains 

breaker

(1)

Aux mains

cable

Output 

breaker

Output 

cable

Battery 

cable

Battery

fuse

[ V ]

[ V ]

[ A ]

[ A ]

[ mm

2

 ]

[ A ]

[ mm

2

 ]

[ A ]

[ mm

2

 

]

[  mm

2

 ]

[ A ]

1

230/400

230/400

50

0,5

35 

(3)

50

35 

(3)

50

35 

(3)

35 

(3)

50

2

230/400

230/400

75

0,5

35 

(3)

75

35 

(3)

75

35 

(3)

35 

(3)

100

3

230/400

230/400

125

0,5

35 

(3)

125

35 

(3)

125

35 

(3)

35 

(3)

150

4

230/400

230/400

150

0,5

50

150

50

150

50

50

200

5

230/400

230/400

200

0,5

70

200

70

200

70

70

250

6

230/400

230/400

250

0,5

95 

(4)

250

95 

(4)

250

95 

(4)

95 

(4)

300

1.  Recommended magneto thermal switch: four poles with intervention threshold 

 10 In

2.   Caution! Use type B four-pole selective (S) type differentials. load leakage currents are added to those generated by the UPS and during transi-

tory phases (power failure and power return) short current peaks may occur. If loads with high leakage current are present, adjust the differential 
protection. It is advisable in all cases to carry out a preliminary check on the earth current leakage with the UPS installed and operational with the 
definitive load, so as to prevent the sudden activation of the above switches.

3.  Minimum section acceptable for the UPS’s sockets. Use the same section also for rigid cables.

4. Maximum section acceptable for the UPS’s sockets is 95 mm

2

.

The UPS is designed for transitory overvoltages in category II installations. If the UPS is part of the building’s 
electric circuit or if it is likely to be subject to transitory overvoltages in category III installations, further exter-
nal protection must be provided, either on the UPS  or in the AC power supply network to the UPS.

In the event of three-phase distorting loads connected in output, the current on the neutral conductor may have 
a value that is 1.5 - 2 times the phase value (also for the input bypass). In this case, size the neutral cables and the 
input/output protection adequately.

Summary of Contents for MODULYS Green Power



































Reviews: