Snell PYXIS System User'S Manual Download Page 14

Page: 14 / 101

HU-PYXIS

PYXIS

System User Guide

A fault signal is available from the fan module relay that can be used within the system as an alarm.
Accessed using the AES/LTC 9-way on the rear panel. See Section 5.1.5 for pin-out details. Details
of setting up the relay are in section 3.1.7.2

3.1.6.2

Replacing the Fan

Figure 8: Replacing a Fan Module

The Fan Module (fan & PCB) is designed for easy replacement.

To replace the fan:-

1. Unplug the power connector. Do not remove the connector or desolder leads. The replacement

assembly comes with a pre-fitted cable and plug.

2. Disconnect the Ribbon Connector.

3. Swing the front door open 30 degrees and remove from the frame.

4. Remove the four corner retaining screws.

5. Remove and replace the fan.

WARNING

Do not operate the frame for long periods without the fan running

and the door closed. High risk of overheating and damage

Summary of Contents for PYXIS






































































































Search results

Summary of Contents for PYXIS

Reviews:

Related manuals for PYXIS

Brands by name

Popular brands

Snell PYXIS, System User'S Manual

Search results

Summary of Contents for PYXIS

Reviews:

Related manuals for PYXIS

Brands by name

Popular brands