manualshive.com logo in svg

SMC Networks 7824M/FSW - annexe 1, Management Manual

The SMC Networks 7824M/FSW - annexe 1 is a powerful networking device that requires careful management to maximize its potential. Get the comprehensive Management Manual for this product for free download, exclusively from manualshive.com. This manual offers in-depth instructions and valuable insights to optimize your networking experience. Dive into the details now!

Share
Download
background image

M

ULTICAST

 F

ILTERING

 C

OMMANDS

33-18

Command Mode 

Interface Configuration (Ethernet, Port Channel)

Command Usage 

• A port which is not configured as an MVR receiver or source port can 

use IGMP snooping to join or leave multicast groups using the 
standard rules for multicast filtering.

• MVR receiver ports cannot be members of a trunk. Receiver ports can 

belong to different VLANs, but should not be configured as a 
member of the MVR VLAN. IGMP snooping can be used to allow a 
receiver port to dynamically join or leave multicast groups within the 
MVR VLAN. Multicast groups can also be statically assigned to a 
receiver port using the 

group

 keyword. 

• One or more interfaces may be configured as MVR source ports. A 

source port is able to both receive and send data for multicast groups 
which it has joined through IGMP snooping or which have been 
statically assigned using the 

group

 keyword. 

• The IP address range from 224.0.0.0 to 239.255.255.255 is used for 

multicast streams. MVR group addresses cannot fall within the 
reserved IP multicast address range of 224.0.0.x. 

• Immediate leave applies only to receiver ports. When enabled, the 

receiver port is immediately removed from the multicast group 
identified in the leave message. When immediate leave is disabled, the 
switch follows the standard rules by sending a group-specific query to 
the receiver port and waiting for a response to determine if there are 
any remaining subscribers for that multicast group before removing 
the port from the group list. 

• Using immediate leave can speed up leave latency, but should only be 

enabled on a port attached to one multicast subscriber to avoid 
disrupting services to other group members attached to the same 
interface. 

• Immediate leave does not apply to multicast groups which have been 

statically assigned to a port.

• IGMP snooping must be enabled to a allow a subscriber to 

dynamically join or leave an MVR group (see 

ip igmp snooping

 on 

Summary of Contents for 7824M/FSW - annexe 1













































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 7824M/FSW - annexe 1

E-Trailer E-Switch Product Manual preview
E-Switch
Brand: E-Trailer Pages: 8
FLIR ACCDPS281B Quick Start Manual preview
ACCDPS281B
Brand: FLIR Pages: 2
Penguin Edge RTM-ATCA-F140 Quick Start Manual preview
Edge RTM-ATCA-F140
Brand: Penguin Pages: 2
AdLuminis 324002 Quick Start Manual preview
324002
Brand: AdLuminis Pages: 8
Xantech 680-10 Installation Instructions preview
680-10
Brand: Xantech Pages: 4
AbleNet SCATIR 51100 Manual preview
SCATIR 51100
Brand: AbleNet Pages: 12
A2A Simulations BONANZA ACCU-SIM V35B Manual preview
BONANZA ACCU-SIM V35B
Brand: A2A Simulations Pages: 112
Asante FRIENDLYNET FS4116R Quick Installation Manual preview
FRIENDLYNET FS4116R
Brand: Asante Pages: 6
GarrettCom DS60s Installation And User Manual preview
DS60s
Brand: GarrettCom Pages: 39
Electroswitch 31201B User Manual preview
31201B
Brand: Electroswitch Pages: 6
Cabletron Systems FlowPoint 2100 12 User Manual preview
FlowPoint 2100 12
Brand: Cabletron Systems Pages: 36
Hawking PN824ES Specifications preview
PN824ES
Brand: Hawking Pages: 2
F&F PF-421 TRMS Manual preview
PF-421 TRMS
Brand: F&F Pages: 10
Quintech RFS 0702 Operation And Adjustment Procedure preview
RFS 0702
Brand: Quintech Pages: 2
N-Tron 302MC-XX Installation Manual preview
302MC-XX
Brand: N-Tron Pages: 16
Hama 00176551 Operating Instructions Manual preview
00176551
Brand: Hama Pages: 56
B&B Electronics UHR304 Quick Start Manual preview
UHR304
Brand: B&B Electronics Pages: 2
IPGARD SA-DPH-4Q-P Quick Start Manual preview
SA-DPH-4Q-P
Brand: IPGARD Pages: 2

Brands by name

Popular brands

Load more brands