manualshive.com logo in svg

SMC Networks 7824M/FSW - annexe 1, Management Manual

Share
Download
SMC Networks 7824M/FSW - annexe 1 Management Manual Download Page 235

D

ISPLAYING

 G

LOBAL

 S

ETTINGS

11-5

make it return to a discarding state; otherwise, temporary data loops 
might result.

•

Designated Root

 – The priority and MAC address of the device in the 

Spanning Tree that this switch has accepted as the root device.
-

Root Port

 – The number of the port on this switch that is closest to 

the root. This switch communicates with the root device through this 
port. If there is no root port, then this switch has been accepted as the 
root device of the Spanning Tree network.

-

Root Path Cost

 – The path cost from the root port on this switch to 

the root device.

•

Configuration Changes

 – The number of times the Spanning Tree has 

been reconfigured.

•

Last Topology Change

 – Time since the Spanning Tree was last 

reconfigured.

These additional parameters are only displayed for the CLI:
•

Spanning tree mode

 – Specifies the type of spanning tree used on this 

switch: 
-

STP

: Spanning Tree Protocol (IEEE 802.1D)

-

RSTP

: Rapid Spanning Tree (IEEE 802.1w)

-

MSTP

: Multiple Spanning Tree (IEEE 802.1s)

•

Instance

 – Instance identifier of this spanning tree. (This is always 0 for 

the CIST.)

•

VLANs configuration

 – VLANs assigned to the CIST.

•

Priority

 – Bridge priority is used in selecting the root device, root port, 

and designated port. The device with the highest priority (i.e., lower 
numeric value) becomes the STA root device. However, if all devices 
have the same priority, the device with the lowest MAC address will then 
become the root device. 

•

Root Hello Time

 – Interval (in seconds) at which this device transmits 

a configuration message. 

•

Root Maximum Age

 – The maximum time (in seconds) this device can 

wait without receiving a configuration message before attempting to 
reconfigure. All device ports (except for designated ports) should receive 

Summary of Contents for 7824M/FSW - annexe 1













































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands