manualshive.com logo in svg

SMC Networks 6752AL2 - annexe 1, Management Manual

The SMC Networks 6752AL2 - annexe 1 is a high-quality networking product that provides seamless connectivity for your home or office. To ensure a hassle-free installation, the comprehensive Installation Manual is available for free download at manualshive.com. Access this manual and unleash the full potential of your SMC Networks 6752AL2 - annexe 1.

Share
Download
background image

P

ORT

 C

ONFIGURATION

3-93

automatically negotiate a trunked link with LACP-configured ports on 
another device. You can configure any number of ports on the switch as 
LACP, as long as they are not already configured as part of a static trunk. If 
ports on another device are also configured as LACP, the switch and the 
other device will negotiate a trunk link between them. If an LACP trunk 
consists of more than four ports, all other ports will be placed in a standby 
mode. Should one link in the trunk fail, one of the standby ports will 
automatically be activated to replace it. 

Command Usage

Besides balancing the load across each port in the trunk, the other ports 
provide redundancy by taking over the load if a port in the trunk fails. 
However, before making any physical connections between devices, use 
the web interface or CLI to specify the trunk on the devices at both ends. 
When using a port trunk, take note of the following points: 

•

Finish configuring port trunks before you connect the corresponding 
network cables between switches to avoid creating a loop. 

•

You can create up to four trunks on the switch, with up to four ports 
per trunk.

•

The ports at both ends of a connection must be configured as trunk 
ports.

•

When configuring static trunks on switches of different types, they 
must be compatible with the Cisco EtherChannel standard.

•

The ports at both ends of a trunk must be configured in an identical 
manner, including communication mode (i.e., speed, duplex mode and 
flow control), VLAN assignments, and CoS settings.

•

Any of the Gigabit ports on the front panel can be trunked together, 
including ports of different media types.

•

All the ports in a trunk have to be treated as a whole when moved 
from/to, added or deleted from a VLAN.

•

STP, VLAN, and IGMP settings can only be made for the entire trunk.

Summary of Contents for 6752AL2 - annexe 1





































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 6752AL2 - annexe 1

D-Link DSL-500 Command Reference Manual preview
DSL-500
Brand: D-Link Pages: 15
D-Link DSN-4100 Series Quick Start Manual preview
DSN-4100 Series
Brand: D-Link Pages: 2
D-Link DWL-G550 Product Data Sheet preview
DWL-G550
Brand: D-Link Pages: 2
Lantronix Device Server UDS 10 Hardware Manual preview
Device Server UDS 10
Brand: Lantronix Pages: 8
Watchguard Firebox T15 Quick Start Manual preview
Firebox T15
Brand: Watchguard Pages: 39
4G Systems XSBox MOVE Quick Start Manual preview
XSBox MOVE
Brand: 4G Systems Pages: 2
QNAP Turbo NAS TVS-71 Series Hardware User Manual preview
Turbo NAS TVS-71 Series
Brand: QNAP Pages: 51
Westermo Ibex-RT-330-HV User Manual preview
Ibex-RT-330-HV
Brand: Westermo Pages: 34
Wave Wireless Networking SPEEDLAN 4100 Installation And Operation User Manual preview
SPEEDLAN 4100
Brand: Wave Wireless Networking Pages: 167
Paradyne 8310 MVLt User Manual preview
8310 MVLt
Brand: Paradyne Pages: 108
ENKHO 154699.01 Original Instructions Manual preview
154699.01
Brand: ENKHO Pages: 48
Inter-m S- Media Manual preview
S- Media
Brand: Inter-m Pages: 20
Baileigh 1019072 Operator'S Manual preview
1019072
Brand: Baileigh Pages: 20
Moxa Technologies WDR-3124A User Manual preview
WDR-3124A
Brand: Moxa Technologies Pages: 94
NETGEAR Insight WAC540 User Manual preview
Insight WAC540
Brand: NETGEAR Pages: 232
Ubiquiti 3GStation Carrier Quick Start Manual preview
3GStation Carrier
Brand: Ubiquiti Pages: 24
SEOWON INTECH SWC-2100 (VoIP CPE) User Manual preview
SWC-2100 (VoIP CPE)
Brand: SEOWON INTECH Pages: 46
Cisco uBR10-LCP2-MC28C Installation Manual preview
uBR10-LCP2-MC28C
Brand: Cisco Pages: 26

Brands by name

Popular brands

Load more brands