SMAY SCD Operation And Maintenance Manual Download

Page: 70 / 81

Operation and Maintenance Manual

– SCD Smoke Dampers

Version 1
Date 04 2018

Page 70 of 81

Operating temperature range

from

–25 °C to +55 °C

Ingress

Protection

Rating

the

housing

IP 21C

Weight

~184 g

Dimensions

Ø 115 x 70 mm

Interoperating junction box

PIP-1AN

6.5.

SO-PD11 OPTICAL INDICATOR

Rys. 52. SO-Pd11 optical indicator.

It is designed for optical signalling with a set of LEDs in fire detection systems.
The indicator is designed for mounting in closed spaces. It generates 3 different flash

rates. It is possible to turn on the continuous light.

Technical Data:

•

Type of signalling device

optical

•

Supply voltage

24 V DC

•

Quiescent current

0 mA

•

Current consumption at alarm state

< 60 mA

•

Ingress Protection Rating of the

housing

IP 53D

•

Weight

~150 g

•

Dimensions

Ø 115 x 63 mm

•

Interoperating junction box

PIP-3AN

6.6.

RT 2 EMERGENCY PUSH BUTTON

Rys. 53. RT 2 Emergency Push Button

RAUCHARZUG

Summary of Contents for SCD


















































































Search results

Summary of Contents for SCD

Reviews:

Related manuals for SCD

Brands by name

Popular brands

SMAY SCD, Operation And Maintenance Manual

Search results

Summary of Contents for SCD

Reviews:

Related manuals for SCD

Brands by name

Popular brands