manualshive.com logo in svg

SMAY SCD, Operation And Maintenance Manual

Share
Download
SMAY SCD Operation And Maintenance Manual Download Page 49

Operation and Maintenance Manual 

– SCD Smoke Dampers 

Version 1  
Date 04 2018 

Page 49 of 81 

 

Rys. 31. PLZ ventilation box. 

Technical Data: 

•

  Maximum operating pressure 10 bar,  

•

  Operating temperature range -200C to +600C,  

•

 

Ø6/4 pipe connection 

 

Types of PZL boxes:  
For ventilation only: 

•

  PLZ 10.0.1: 1 ventilation section with a lever externally accessible and a pressure 

regulator with a filter; dimensions: 300 x 200 x 80 mm 

•

  PLZ  10.0.2:  2  ventilation  sections  with  two  levers  externally  accessible  and  a 

pressure regulator with a filter; dimensions: 300 x 270 x 100 mm 

For 

A mode (“open only”) + ventilation: 

•

  PLZ  20.1.1:  1  section for 

A mode (“open only”), 1 ventilation section with a lever 

externally  accessible  and  a  pressure  regulator  with  a  filter;  dimensions: 
300 x 200 x 80 mm 

•

  PLZ  20.1.2:  1  section  for 

A  mode  (“open  only”),  2  ventilation  sections  with  two 

levers  externally  accessible  and  a  pressure  regulator  with  a  filter;  dimensions: 
300 x 270 x 100 mm 

For AZ mode (“open-close”) + ventilation: 

•

 

PLZ 30.1.1: 1 section for AZ mode (“open-close”), 1 ventilation section with a lever 
externally  accessible  and  a  pressure  regulator  with  a  filter;  dimensions: 
300 x 200 x 80 mm  

•

 

PLZ 30.1.2: 1 section for AZ mode (“open-close”), 2 ventilation sections with two 
levers  externally  accessible  and  a  pressure  regulator  with  a  filter;  dimensions: 
300 x 270 x 100 mm  

•

 

PLZ 30.2.2: 2 sections for AZ mode (“open-close”), 2 ventilation sections with two 
levers  externally  accessible  and  a  pressure  regulator  with  a  filter;  dimensions: 
300 x 270 x 100 mm 

In  designations  of PZL boxes  with  a  ventilation lever  that  is  not  accessible from  the 

outer side, “1” is a second digit (PZL 11.x.x, PZL 21.x.x, PZL 31.x.x). 

Other  versions,  including  remote  control  (electric  or  pneumatic),  are  available  on 

individual request. 

Summary of Contents for SCD


















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands