manualshive.com logo in svg

SMAY SCD, Operation And Maintenance Manual

Share
Download
SMAY SCD Operation And Maintenance Manual Download Page 54

Operation and Maintenance Manual 

– SCD Smoke Dampers 

Version 1  
Date 04 2018 

Page 54 of 81 

5.2. 

ELECTRIC DRIVES 

5.2.1.  CONFIGURATION 

Dampers with an electric drive are equipped with 24 V actuators. The same actuator 

supports emergency operation and ventilation functions. 

The  elements  of  the  system  equipment  are  as  follows:  control  panel,  24 V DC, 

Manual emergency push button. 

Activation in emergency mode may take place: 

•

  Automatically 

–  by  means  of  an  electric  signal,  sent  by  smoke  or  temperature 

detectors. 

•

  Automatically 

– from the Fire Alarm System (Polish acronym SAP) 

•

  Manually 

–  if  fire  has  been  noticed,  a  member  of  staff  pushes  the  manual 

emergency push button. 

The  continuity  of  power  supply  is  imperative  for  this.  Non-combustible  cables  are 

used to connect elements of the system. 

 

1.  Smoke extraction system control panel 
2.  SAP control panel 
3.  Emergency push button 
4.  Smoke detector 
5.  Ventilation push button 
6.  Weather station 
7.  Alarm signalling device 

Rys. 37. 

The “B” type damper with an electric actuator, control panel and weather control panel. 

The  exemplary  scheme  of  the  damper  opening  control  as  the  function  of  smoke 

extraction and ventilation is shown in Fig. 38. 
Manual or automatic opening after the limit temperature has been reached or opening with 
SAP signal (with an electric module). Ventilation with an electric actuator. 

SAP control panel option 

Summary of Contents for SCD


















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands