SMAY SCD Operation And Maintenance Manual Download Page 40

Page: 40 / 81

Operation and Maintenance Manual

– SCD Smoke Dampers

Version 1
Date 04 2018

Page 40 of 81

Technical Data:

Maximum static operating pressure

80 bar

Maximum dynamic operating pressure

80 bar

Valve nominal diameter

2 mm

Pin nominal diameter

2 mm

Operating temperature range

-250

°C to +1100 °C

In systems carrying out the “A” “open only” operating mode, TAVE thermal trips are

used.

Channels marking:
VA

“Open” input

“Open” output

Rys. 19. TAVE thermal trip

Types of TAVE thermal trips:

Type

Vent valve

A Cylinder thread

TAVE 3.01

1/2" UNF (standard)

TAVE 3.01-M

M18 x 1.5

TAVE 3.01-F

W21.8 x 1/14"

TAVE 3.11

yes

1/2" UNF (standard)

TAVE 3.11-M

yes

M18 x 1.5

TAVE 3.11-F

yes

W21.8 x 1/14"

VA input in standby mode (the valve enabled

–disabled) is connected with the CA

output, which makes it possible, among other things, to carry out the damper ventilation
function without any interruption. Option with venting:

CA output in standby mode is vented by means of an integrated drain (vent) valve.

After pressurising VA input (from the alarm or ventilation box), connection between VA
input and CA output is set up.
Installation:

1. Make the following connections:

– OPEN side of the actuator

– OPEN ventilation or smoke extraction circuit

Summary of Contents for SCD


















































































Search results

Summary of Contents for SCD

Reviews:

Brands by name

Popular brands

SMAY SCD, Operation And Maintenance Manual

Search results

Summary of Contents for SCD

Reviews:

Brands by name

Popular brands