manualshive.com logo in svg

SMAY SCD, Operation And Maintenance Manual

Share
Download
SMAY SCD Operation And Maintenance Manual Download Page 65

Operation and Maintenance Manual 

– SCD Smoke Dampers 

Version 1  
Date 04 2018 

Page 65 of 81 

Close-Down 

•

  Disconnect  the  batteries  from  the  control  panel  (e.g.  disconnect  the  battery 

connection cable or F2 fuse). Turn off the mains voltage. 

•

  The end user, i.e. the last owner, shall hand over worn batteries to the distributor 

or appropriate waste treatment plant. This obligation applies to both individual end 
users and company end users. 

 
In regard to the control panels, this Operation and Maintenance Manual contains only 

basic  technical  data  and  information  about  installation,  start-up,  maintenance  and  close-
down. Both the Installer and the User are required to know and apply the complete version 
of the “Installation and Operation Manual”, which is provided along with the control panel. 

6.  SYSTEM EQUIPMENT 

6.1. 

WRS 2B WEATHER CONTROL PANEL 

Required signal is sent by four separate potential-free change-over  contacts (output 

contacts).  The  contacts  remain  active  as  long  as  the  detector  operates,  and  the  contact 
minimum operating time is equal to 6 minutes. 

WM  wind  detector  and/or  RS  rain  detector  are  connected  to WRS  2b  control  panel. 

As expected, operation is achieved by regulation of the trigger threshold for the signal from 
the wind/smoke detector. 

Functional capabilities of the control panel (to set) are as follows: 

“Limited wind sensitivity” (it is possible to close only if the wind persists). 
“Continuous heating” (the rain detector is heated continuously). 
“Contact  programming”  (contacts  3  and  4  optionally  switch  over  during  the  rain  and/or 
wind). 
“Output inactive” (relays are not energised for the service/maintenance time). 
“Close  time  shortening”  (minimum  delay  in  actuators  closing  is  decreased  from  6  to 
3 minutes). 
“Failure” (contact 2 will switch in case of failure of the rain detector). 
“Test” (a function that makes it possible to test the detectors and actuators operation). 

The  active  status  of  the  control  panel  is  indicated  with  a  LED:  I  readiness, W  wind 

and R rain. 

 

Rys. 48. WRS 2B weather control panel 

Summary of Contents for SCD


















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands