SMAY SCD Operation And Maintenance Manual Download

Page: 33 / 81

Operation and Maintenance Manual

– SCD Smoke Dampers

Version 1
Date 04 2018

Page 33 of 81

1450

2690

965+h

2.1

275.0

1500

2765

995+h

2.25

290.0

1500

1700

2765

995+h

2.55

310.0

1500

1800

2765

995+h

2.70

320.0

1600

2940

1060+h

2.56

310.0

1600

1700

2940

1060+h

2.72

320.0

1600

1800

2940

1060+h

2.88

330.0

1700

3120

1125+h

2.89

330.0

1700

1800

3120

1125+h

3.06

340.0

1800

3295

1190+h

3.24

350.0

SCD-1-W smoke dampers are classified according to PN-EN 12101-2 criteria, with

reference to the following areas:

•

Reliability: double action, Re 1000,

•

Snow load: SL 550

•

Low temperature: T(-25) Wind load: WL 1500

•

Resistance to high temperature: B300

•

The active

area of the dampers with a roof hatch function, with w ≤ 1200

dimension is smaller by 3% than the area of standard version dampers.

•

The active area of the dampers with a roof hatch function, with w > 1200

dimension is equal to the area of standard version dampers.

•

It is possible to make the dampers in the version meeting the requirements of the

BROOF(t1) classification.

4.8.

OPTIONAL ACCESSORIES

4.8.1. WIND DEFLECTORS

Wind deflectors are to maximize the active area of smoke dampers. They are used

when expected impact of wind would decrease the active area of a smoke damper. These
are profiled elements made of galvanised steel sheet, optimized during aerodynamic tests.

Deflectors are mounted to a damper base with the use of the bolted connection.

Rys. 9. Wind deflector.

H height

L1 length

L2 length

Summary of Contents for SCD


















































































Search results

Summary of Contents for SCD

Reviews:

Related manuals for SCD

Brands by name

Popular brands

SMAY SCD, Operation And Maintenance Manual

Search results

Summary of Contents for SCD

Reviews:

Related manuals for SCD

Brands by name

Popular brands