background image

DTC Interpretation listing

P0016–CRANKSHAFT / CAMSHAFT TIMING MISALIGNMENT
P0030-1/1 02 SENSOR HEATER RELAY MALFUNCTION
P0036-1/1 02 SENSOR HEATER RELAY MALFUNCTION
P0071-AMBIENT AIR TEMPERATURE SENSOR 

PERFORMANCE 

P0072-AMBIENT AIR TEMPERATURE SENSOR CIRCUIT LOW
P0088-FUEL RAIL PRESSURE SIGNAL IS ABOVE MAX LIMIT 
P0101-MAF SENSOR PERFORMANCE
P0102-MAF SENSOR LOW FREQUENCY
P0103-MAF SENSOR HIGH FREQUENCY
P0106-BAROMETRIC PRESSURE OUT OF RANGE
P0107-MAP SENSOR VOLTAGE TOO LOW
P0108–MAP SENSOR VOLTAGE TOO HIGH 
P0111-INTAKE AIR TEMP PERFORMANCE 
P0112-INTAKE AIR TEMP SENSOR VOLTAGE TOO LOW 
P0113-INTAKE AIR TEMP SENSOR VOLTAGE TOO HIGH 
P0116–ENGINE COOLANT TEMPERATURE SENSOR CIRCUIT 

PERFORMANCE

P0117-ENGINE COOLANT TEMPERATURE (ECT) SENSOR 

VOLTAGE TOO LOW 

P0118-ENGINE COOLANT TEMPERATURE (ECT) SENSOR 

VOLTAGE TOO HIGH 

P0121-TP SENSOR VOLTAGE DOES NOT AGREE WITH MAP
P0122-THROTTLE POSITION SENSOR VOLTAGE TOO LOW 
P0123-THROTTLE POSITION SENSOR VOLTAGE TOO HIGH
P0125-INSUFFICIENT COOLANT TEMP FOR CLOSED-LOOP 

FUEL CONTROL 

P0128-THERMOSTAT RATIONALITY 
P0130-1/1 02 SENSOR HEATER RELAY MALFUNCTION
P0131-O2 SENSOR 1/1 CIRCUIT VOLTAGE TOO LOW
P0132-O2 SENSOR 1/1 CIRCUIT VOLTAGE TOO HIGH
P0133-O2 SENSOR 1/1 SLOW RESPONSE 
P0134-02 SENDOR 1/1 STAYS AT CENTER
P0135-O2 SENSOR 1/1 HEATER PERFORMANCE 
P0136-O2 SENSOR 1/2 HEATER CIRCUIT MALFUNCTION
P0137-O2 SENSOR 1/2 CIRCUIT LOW 
P0138-O2 SENSOR 1/2 CIRCUIT HIGH
P0139-O2 SENSOR 1/2 SLOW RESPONSE 
P0140-02 SENSOR 1/2 STAYS AT CENTER
P0141-02 SENSOR 1/2 RELAY
P0143-02 SENSOR 1/3 SHORTED TO GROUND
P0144-02 SENSOR 1/3 SHORTED TO VOLTAGE
P0145-02 SENSOR 1/3 SLOW RESPONSE
P0146-02 SENSOR 1/3 STAYS AT CENTER
P0147-02 SENSOR 1/3 HEATER FAILURE
P0148-FUEL DELIVERY ERROR
P0151-O2 SENSOR 2/1 CIRCUIT LOW 
P0152-O2 SENSOR 2/1 CIRCUIT HIGH 
P0153-O2 SENSOR 2/1 SLOW RESPONSE
P0154-O2 SENSOR 2/1 STAYS AT CENTER
P0155-O2 SENSOR 2/1 HEATER PERFORMANCE
P0157-O2 SENSOR 2/2 CIRCUIT VOLTAGE TOO LOW
P0158-O2 SENSOR 2/2 CIRCUIT VOLTAGE TOO HIGH
P0159-O2 SENSOR 2/2 SLOW RESPONSE 
P0160-O2 SENSOR 2/2 STAYS AT CENTER
P0161-O2 SENSOR 2/2 HEATER PERFORMANCE
P0168-DECREASED ENGINE PERFORMANCE DUE TO HIGH 

INJECTION PUMP FUEL TEMPERATURE

P0169-WATER IN FUEL (WIF) LIGHT ON TOO LONG
P0171-FUEL SYSTEM 1/1 LEAN 
P0172-FUEL SYSTEM 1/1 RICH 
P0174-FUEL SYSTEM 2/1 LEAN 
P0175-FUEL SYSTEM 2/1 RICH 
P0176-LOSS OF FLEX FUEL CALIBRATION SIGNAL
P0177-WATER IN FUEL
P0178-WATER IN FUEL SENSOR VOLTAGE TOO LOW
P0178-FLEX FUEL SENSOR VOLTAGE TOO LOW
P0180-CNG TEMP SENSOR VOLTAGE FAIL
P0181-FUEL PUMP INJECTION PUMP FAILURE
P0182-CNG TEMP SENSOR VOLTAGE TOO LOW
P0183-CNG TEMP SENSOR VOLTAGE TOO HIGH
P0192-FUEL RAIL PRESSURE SENSOR VOLTAGE TOO LOW 
P0193-FUEL RAIL PRESSURE SENSOR VOLTAGE TOO HIGH
P0201-INJECTOR #1 CONTROL CIRCUIT 
P0202-INJECTOR #2 CONTROL CIRCUIT 
P0203-INJECTOR #3 CONTROL CIRCUIT 
P0204-INJECTOR #4 CONTROL CIRCUIT 
P0205-INJECTOR #5 CONTROL CIRCUIT 

P0206-INJECTOR #6 CONTROL CIRCUIT
P0207-FUEL INJECTOR 7 CIRCUIT 
P0208-FUEL INJECTOR 8 CIRCUIT 
P0209-FUEL INJECTOR 9 CIRCUIT 
P0210-FUEL INJECTOR 10 CIRCUIT 
P0215-FUEL INJECTOR PUMP CONTROL CIRCUIT
P0216-FUEL INJECTOR PUMP TIMING FAILURE
P0217-DECREASED ENGINE PERFORMANCE DUE TO ENGINE

OVERHEAT CONDITION

P0219-CRANKSHAFT POSITION SENSOR OVER SPEED 

SIGNAL 

P0220-APP SENSOR 2 CIRCUIT
P0221-APP SENSOR 2 PERFORMANCE 
P0222-APP SENSOR 2 CIRCUIT LOW
P0222-IDLE VALIDATION SIGNALS BOTH LOW
P0223-INJECTION PULSE WIDTH ERROR (RISE TIME LONG)
P0223-IDLE VALIDATION SIGNALS BOTH HIGH (ABOVE 5V)
P0225-APP SENSOR 3 CIRCUIT
P0226-APP SENSOR 3 CIRCUIT PERFORMANCE
P0227-APP SENSOR 2 CIRCUIT LOW VOLTAGE
P0228-APP SENSOR 2 CIRCUIT HIGH VOLTAGE
P0230-TRANSFER PUMP (LIFT PUMP) CIRCUIT OUT OF 

RANGE

P0231-FUEL PUMP FEEDBACK CIRCUIT LOW VOLTAGE
P0232-FUEL SHUT-OFF SIGNAL VOLTAGE TOO HIGH
P0234-TURBOCHARGER OVERBOOST CONDITION 
P0236-MAP SENSOR TOO HIGH TOO LONG 
P0237-MAP SENSOR VOLTAGE TOO LOW
P0238-MAP SENSOR VOLTAGE TOO HIGH 
P0243-OPEN OR SHORTED CONDITION DETECTED IN THE 

TURBOCHARGER WASTEGATE SOLENOID CONTROL

P0251-FUEL INJECTION PUMP FUEL VALVE FEEDBACK 

CIRCUIT

P0252-FUEL INJECTION PUMP FUEL VALVE STUCK
P0253-FUEL INJECTION PUMP FUEL VALVE OPEN CIRCUIT
P0254-FUEL INJECTION PUMP FUEL VALVE CURRENT TOO 

HIGH

P0263-CYLINDER 1 BALANCE SYSTEM
P0266-CYLINDER 2 BALANCE SYSTEM
P0269-CYLINDER 3 BALANCE SYSTEM
P0272-CYLINDER 4 BALANCE SYSTEM
P0275-CYLINDER 5 BALANCE SYSTEM
P0278-CYLINDER 6 BALANCE SYSTEM
P0281-CYLINDER 7 BALANCE SYSTEM
P0284-CYLINDER 8 BALANCE SYSTEM
P0300-MULTIPLE CYLINDER MISFIRE 
P0301-CYLINDER # 1 MISFIRE 
P0302-CYLINDER # 2 MISFIRE 
P0303-CYLINDER # 3 MISFIRE 
P0304-CYLINDER # 4 MISFIRE
P0305-CYLINDER # 5 MISFIRE 
P0306-CYLINDER # 6 MISFIRE 
P0307-CYLINDER #7 MISFIRE 
P0308-CYLINDER #8 MISFIRE 
P0309-CYLINDER #9 MISFIRE 
P0310-CYLINDER #10 MISFIRE 
P0320–NO CRANK REFERENCE SIGNAL AT PCM
P0325-KNOCK SENSOR 1 CIRCUIT .
P0327-KNOCK SENSOR NOISE CHANNEL LOW VOLTAGE
P0330-KNOCK SENSOR 2 CIRCUIT 
P0335-CRANKSHAFT POSITION SENSOR CIRCUIT
P0336-CRANKSHAFT POSITION (CKP) SENSOR SIGNAL 
P0337-CRANKSHAFT POSITION (CKP) SENSOR VOLTAGE 

TOO LOW

P0338-CRANKSHAFT POSITION (CKP) SENSOR VOLTAGE 

TOO HIGH 

P0339-CRANKSHAFT POSITION SENSOR INTERMITTENT 
P0340-CAMSHAFT POSITION (CMP) LOST 
P0341-CAMSHAFT POSITION (CMP) SENSOR SIGNAL 
P0342-ESS VOLTAGE SUPPLY LOW
P0343-ESS VOLTAGE SUPPLY HIGH
P0350-IGNITION COIL DRAWN TOO MUCH CURRENT
P0351-IGNITION COIL #1 PRIMARY CIRCUIT
P0352-IGNITION COIL #2 PRIMARY CIRCUIT 
P0353-IGNITION COIL #3 PRIMARY CIRCUIT 
P0354-IGNITION COIL #4 PRIMARY CIRCUIT 
P0355-IGNITION COIL #5 PRIMARY CIRCUIT 
P0356-IGNITION COIL #6 PRIMARY CIRCUIT 

Page 16 of 20

Summary of Contents for S-03






















Reviews: