Skyworks Si5391 Reference Manual Download Page 92

Page: 92 / 94

Table 15.105. 0x0B44 Loss of Signal Clock Disable

Reg Address

Bit Field

Type

Setting Name

Description

0x0B44

3:0

R/W

PDIV_ENB

Clock disable for the fractional divide of the input P
dividers. [P3, P2, P1, P0]. Must be set to 0 if the P
divider has a fractional value.

0: Enable the clock to the fractional divide part of the P
divider

1: Disable the clock to the fractional divide part of the P
divider

Table 15.106. 0x0B4A Divider Clock Disables

Reg Address

Bit Field

Type

Setting Name

Description

0x0B4A

4:0

R/W

N_CLK_DIS

Controls the clock to the N divider. If an N divider is
used the corresponding bit must be 0. [N3 N2 N1 N0].
See also registers 0x0A03 and 0x0A05.

Table 15.107. 0x0B57

Reg Address

Bit Field

Type

Name

Description

0x0B57

7:0

R/W

VCO_RESET_CAL-

CODE

12-bit value

0x0B58

11:8

R/W

VCO_RESET_CAL-

CODE

Si5391 Reference Manual • Si5391A/B Register Map

Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com

Rev. 0.5 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • January 11, 2022

Summary of Contents for Si5391































































































Search results

Summary of Contents for Si5391

Reviews:

Related manuals for Si5391

Brands by name

Popular brands

Skyworks Si5391, Reference Manual

Search results

Summary of Contents for Si5391

Reviews:

Related manuals for Si5391

Brands by name

Popular brands