Skyworks Si5391 Reference Manual Download Page 88

Page: 88 / 94

Table 15.84. 0x094A Input Clock Routing Enable

Reg Address

Bit Field

Type

Setting Name

Description

0x094A

6:4

R/W

INx_TO_PFD_EN

When = 1, enables the routing of the 3 input clocks
IN0,1,2 to the Phase Detector. Each bit corresponds
to the inputs as follows [6:4] = [IN2 IN1 IN0]. IN_SEL
is used to select the input clock that is applied to the
phase detector.

Table 15.85. 0x095E

Reg Address

Bit Field

Type

Setting Name

Description

0x095E

R/W

M_INTEGER

Set by CBPro

Si5391 Reference Manual • Si5391A/B Register Map

Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com

Rev. 0.5 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • January 11, 2022

Summary of Contents for Si5391































































































Search results

Summary of Contents for Si5391

Reviews:

Related manuals for Si5391

Brands by name

Popular brands

Skyworks Si5391, Reference Manual

Search results

Summary of Contents for Si5391

Reviews:

Related manuals for Si5391

Brands by name

Popular brands