Skyworks Si5386 Reference Manual Download Page 55

Page: 55 / 133

Table 5.1. Zero Delay Mode Registers

Register Name

Hex Address [Bit Field]

Function

OUTX_ALWAYS_ON

0x013F[7:0]
0x0140[3:0]

Force ZDM output always on.

0x000: Do not force output on (default)

0x800: Force OUT9A always on for ZDM

ZDM_EN

0x0487[0]

Enable ZDM operation.

0: Disable ZDM (default)

1: Enable ZDM operation

ZDM_IN_SEL

0x0487[2:1]

ZDM Manual Input Select when both ZDM_EN = 1 and
IN_SEL_REGCTRL (0x052A[0]) = 1.

0: IN0 (default)

1: IN1

2: IN2

3: Reserved (IN3 already used by ZDM)

IN_SEL_REGCTRL

0x052A[0]

ZDM Manual Input Select control source.

0: Pin controlled input clock selection (default)

1: ZDM_IN_SEL register input clock selection for ZDM

Note:

1. When ZDM_EN = 1 and IN_SEL_REG_CTRL = 1, the IN_SEL pins and register bits have no effect.

Table 5.2. Input Clock Selection in Zero Delay Mode

ZDM_EN

IN_SEL_REGCTRL

Input Clock Selection Governed by:

IN_SEL[1:0] Pins

IN_SEL Register

IN_SEL[1:0] Pins (ZDM)

ZDM_IN_SEL Register (ZDM)

Si5386 Rev. E Reference Manual • Zero Delay Mode

Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com

Rev. 1.2 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 9, 2021

Summary of Contents for Si5386






































































































































Search results

Summary of Contents for Si5386

Reviews:

Related manuals for Si5386

Brands by name

Popular brands

Skyworks Si5386, Reference Manual

Search results

Summary of Contents for Si5386

Reviews:

Related manuals for Si5386

Brands by name

Popular brands