Skyworks Si5386 Reference Manual Download Page 92

Page: 92 / 133

Table 12.69. Register 0x0104 OUT0A Output Format and Configuration

Reg Address

Bit Field

Type

Name

Description

0x0104

2:0

R/W

OUT0A_FORMAT

Select output format.

0: Reserved

1: Differential Normal
mode

2: Differential Low-Power
mode

3: Reserved

4: LVCMOS single ended

5: LVCMOS (OUTx pin
only)

6: LVCMOS (OUTxb pin
only)

7: Reserved

0x0104

R/W

OUT0A_SYNC_EN

Synchronous Enable/Dis-
able selection.

0: Asynchronous Ena-
ble/Disable (default)

1: Synchronous Ena-
ble/Disable (Glitchless)

0x0104

5:4

R/W

OUT0A_DIS_STATE

Determines the logic
state of the output driver
when disabled:

0: Disable logic Low

1: Disable logic High

2-3: Reserved

0x0104

7:6

R/W

OUT0A_CMOS_DRV

LVCMOS output impe-
dance selection. See

Ta-

ble 4.8 LVCMOS Out-
put Impedance and Drive
Strength Selections on
page 44

for valid selec-

tions.

Table 12.70. Register 0x0105 Output OUT0A Differential Amplitude and Common Mode

Reg Address

Bit Field

Type

Name

Description

0x0105

3:0

R/W

OUT0A_CM

OUT0A Common Mode
Voltage selection. On-
ly applies when
OUT0A_FORMAT=1 or
2.

0x0105

6:4

R/W

OUT0A_AMPL

OUT0A Differential Am-
plitude setting. Only ap-
plies when OUT0A_FOR-
MAT=1 or 2.

Si5386 Rev. E Reference Manual • Register Map

Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com

Rev. 1.2 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 9, 2021

Summary of Contents for Si5386






































































































































Search results

Summary of Contents for Si5386

Reviews:

Related manuals for Si5386

Brands by name

Popular brands

Skyworks Si5386, Reference Manual

Search results

Summary of Contents for Si5386

Reviews:

Related manuals for Si5386

Brands by name

Popular brands