Skyjack SJ9233 RT Operation Manual Download Page 114

Page: 114 / 122

114

221491AFA

SJ9233 RT, SJ9243 RT, SJ9253 RT, SJ9664 RT

Section 8 – Labels

SJ9233 RT, SJ9243 RT, SJ9253 RT & SJ9664 RT labels

Description

Label Pictorial

No pressure washer (dual fuel engine)

Do not use a pressure washer.

Engine controls - dual fuel (optional)

▪

Select the engine start position

to start the engine.

▪

Select the liquid propane gas

or gasoline

as the fuel

type.

LPG

HD5

Engine controls - diesel

▪

Select the engine start position

to start the engine, or

select the glow plug position

to energize the glow plugs

to start a cold diesel engine.

▪

Select the

positive air shut-off

switch

(optional) to stop

the air supply to the engine.

8.3-5 Engine compartment

LPG

HD5

Summary of Contents for SJ9233 RT



























































































































Search results

Summary of Contents for SJ9233 RT

Reviews:

Related manuals for SJ9233 RT

Brands by name

Popular brands

Skyjack SJ9233 RT, Operation Manual

Search results

Summary of Contents for SJ9233 RT

Reviews:

Related manuals for SJ9233 RT

Brands by name

Popular brands