Skyjack SJ9233 RT Operation Manual Download Page 117

Page: 117 / 122

117

SJ9233 RT, SJ9243 RT, SJ9253 RT, SJ9664 RT

221491AFA

SJ9233 RT, SJ9243 RT, SJ9253 RT & SJ9664 RT labels

Section 8 – Labels

Description

Label Pictorial

Hydraulic oil, battery warmer, oil pan/block heater cord

Battery warmer, hydraulic oil heater and oil pan/block heater
heater cord.

Arctic engine oil

Recommended engine oil (0W-40) for the arctic option.

Arctic hydraulic oil

Recommended hydraulic oil (Univis HVI 26) for the arctic option.

UNIVIS HVI

HVLP DIN 51524-3

(VI >376)

Do not leave heaters plugged in

147041AA

Do not leave heaters plugged in for

longer than 12 hours consecutively.

Do not use heater above freezing temperatures

147042AA

Do not use heaters if temperature

is above freezing.

Manufactured

/YYYY

BAR

S/N

8.3-8 Cold/Arctic Package

Summary of Contents for SJ9233 RT



























































































































Search results

Summary of Contents for SJ9233 RT

Reviews:

Related manuals for SJ9233 RT

Brands by name

Popular brands

Skyjack SJ9233 RT, Operation Manual

Search results

Summary of Contents for SJ9233 RT

Reviews:

Related manuals for SJ9233 RT

Brands by name

Popular brands