background image

 

53

SJ9233 RT, SJ9243 RT, SJ9253 RT, SJ9664 RT 

221491AFA

Function tests

 

Section 4 – Inspections Before Operation

4.3-14 Do a test of the horn

1. 

Push the 

horn 

button 

7

.

 

Result:

 The horn makes a sound. 

4.3-15 Do a test of the elevated travel 

speed

 WARNING

Look for overhead obstructions or other possible 
hazards around the MEWP when you raise the 
platform. Do not lower the platform unless the area 
below is clear of personnel and obstructions. If 
you do not obey, there is a risk of death or serious 
injury. 

1. 

Make sure the path of intended motion is clear.

2. 

Raise the platform until it is at a height of 
approximately 4.3 m (14 ft). 

3. 

Drive the MEWP forward and then rearward.

 

Result:

 The MEWP drives slower than when it 

was in the lowered travel position. 

4.3-16 Do a test of the outrigger interlocks 

(optional equipment)

1. 

Use the MEWP ladder to enter the platform. 

2. 

Start the engine. Refer to 

Figure 06

3. 

Move the 

auto-level/differential lock

 switch 

8

 

to the 

auto-level position

 

8a

.

4. 

Squeeze the 

function-enable 

switch 

4

 and 

push the 

controller handle 

5

 to extend all four 

outriggers 10 cm (4 in).

5. 

Move the

 lift/off/drive

 switch 

3

 to the 

lift 

position 

3b

6. 

Squeeze the 

function-enable 

switch 

4

 and 

push the 

controller handle 

5

 to raise the 

platform

 

Result: 

The platform does not raise. 

7. 

Move the 

auto-level/differential lock

 switch 

8

 

to the 

auto-level position 

8a

8. 

Squeeze the 

function-enable 

switch 

4

 and pull 

the 

controller handle

 

5

 to fully retract all four 

outriggers. 

 

Result:

 All four outriggers fully retract.

TM

4

5

3

3b

7

8a

8

Summary of Contents for SJ9233 RT



























































































































Reviews: