81
SJ9233 RT, SJ9243 RT, SJ9253 RT, SJ9664 RT
221491AFA
Move the MEWP through a doorway
Section 6 – Additional Procedures
12.
Unfold the front-left extension guardrail and
install all the
lock-pins
.
13.
Unfold the rear-left extension guardrail and
install all the
lock-pins
.
14.
Remove the lock-pin from the rear-left mid-
rail. Swing the rear guardrail towards the right
extension guardrail. Install all the
lock-pins
.
15.
Remove the lock-pin from the front-right mid-
rail. Swing the front guardrail towards the left
extension guardrail. Install all the
lock-pins
.
16.
Mount the platform control console at the front
right of the platform and install all the
lock-pins
.
WARNING
Before you operate this MEWP, make sure that
the guardrail system does not have loose or
missing lock-pins. The guardrail system must be
in the vertical position. Lock all pins correctly. An
incorrectly locked guardrail can cause a fall, which
can result in death or serious injury.
6.8 Move the MEWP through a
doorway
WARNING
Only do this procedure on level ground. If you do
not obey, there is a risk of death or serious injury.
1.
Make sure the height/width of the doorway is
sufficient to let the MEWP drive through.
2.
Before you operate the MEWP, do a full
inspection of the site (refer to
Section 2.4
).
Identify hazards in your work area.
3.
Make sure the platform is fully lowered.
4.
Follow
Section 6.3-1
to disconnect and remove
the platform control console.
5.
Fold the guardrails if it is necessary. Refer to
Section 6.7
for the procedure on how to fold the
guardrails.
WARNING
Crush hazard. Make sure that there are no
personnel in the path you will travel. Tell personnel
around the path before you move the MEWP. Use
a second person to monitor the movement of
the MEWP. Make sure that person stays at a safe
distance. If you do not obey, there is a risk of death
or serious injury.
6.
Connect the
platform control console cable
to
the
electrical plug
at the rear side of the MEWP.
7.
Stay behind the MEWP.
8.
Make sure the
platform control console
points
in the same direction as the front of the MEWP.
9.
Turn the
main power disconnect
switch to the
on position.
10.
Pull the
emergency-stop
button on the base
control console.
11.
Turn the
off/base/platform key
switch to the
platform position.
12.
Pull the
emergency-stop
button on the platform
control console.
13.
Start the engine. Refer to
Figure 07
.
14.
Move the
inclined drive/level drive
switch
to the inclined drive (low speed/high torque)
position for reduced speed.
15.
Move the
lift/off/drive
switch to the drive
position.
Summary of Contents for SJ9233 RT
