manualshive.com logo in svg

sitrex TR/6-S, Assembly, Use And Maintenance

Share
Download
sitrex TR/6-S Assembly, Use And Maintenance Download Page 47

 

47

 
 
   

NOISE AND VIBRATIONS  
 

The  machine  does  not  have  any  drive  components,  so  the  only  noises  it  makes  are 
that  of  the  teeth  dragging  on  the  ground  and  those  caused  by  machine  vibrations, 
therefore the noise of the tractor always covers that of the machine. 

 

 

 

INFORMATION ON SCRAPPING THE MACHINE   

 
The  machine  consists  mainly  of  ferrous  material,  which  must  be  disposed  of 
according to the regulations in force in the country concerned. 
 
The  plastic  and/or  rubber  parts  must  be  disposed  of  according  to  the  regulations  in 
force in the country concerned. 
   
There  is  also  a  small  amount  of  residual  grease  and  oil,  which  must  be  disposed  of 
according to the regulations in force in the country concerned. 
 
Do  not  release  or  otherwise  dispose  of  any  residues  or  remaining  parts  into  the 
surrounding environment. 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for TR/6-S

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands