Sirona cerec ac Operating Instructions Manual Download Page 26

Page: 26 / 84

6 Installation and startup
6.1 Transport and unpacking

Sirona Dental Systems GmbH

Operating Instructions CEREC AC

Installation and startup

6.1

Transport and unpacking

All products from Sirona are carefully checked prior to shipment. Please
perform an incoming inspection immediately after delivery.

Check the delivery note to ensure that the consignment is complete.

Check whether the product shows any visible signs of damage.

NOTE

Damage during transport

If the product was damaged during transport, please contact your
carrying agent.

If return shipment is required, please use the original packaging for
shipment.

To prevent damage to the LCD monitor, it must be removed during
transport of the unit.

6.2

Disposal of packaging materials

The packaging must be disposed of in compliance with the relevant
national regulations. Please observe the regulations applicable in your
country.

6.3

Scope of supply

The detailed scope of supply is specified in the document "Checklist".

Summary of Contents for cerec ac





















































































Search results

Summary of Contents for cerec ac

Reviews:

Related manuals for cerec ac

Brands by name

Popular brands

Sirona cerec ac, Operating Instructions Manual

Search results

Summary of Contents for cerec ac

Reviews:

Related manuals for cerec ac

Brands by name

Popular brands