Sirona cerec ac Operating Instructions Manual Download Page 48 | Manualshive

Page: 48 / 84

background image

7 Operation
7.7 Acquisition control with CEREC SW

Sirona Dental Systems GmbH

Operating Instructions CEREC AC

48

Automatic acquisition control

To help avoid blurred acquisitions caused by withdrawing the CEREC
camera too early, an acoustic signal sounds as soon as the acquisition
is completed. Make sure that neither the Windows volume control is at
the lowest position nor “Sound off” is activated.

1.

Position the CEREC camera above the powdered preparation as
described.

2.

Once a sharp acquisition is possible, images are generated and
transmitted to the 3D preview automatically.
Observe undercuts on all lateral edge lines of the preparation.

3.

Move the camera until all required images have been acquired.

Ä

The model is restored automatically in the 3D preview during
the acquisition.

4.

Then check the above points once again. Take care that the optical
impression is sufficiently bright, sharp and free of motion blurring. If
you do not observe these points, one of them may have a negative
effect upon the subsequent procedure.

If you click the scan icon of the upper jaw, lower jaw or buccal
registration, you can take additional acquisitions of the upper jaw, lower
jaw or buccal registration.

Manual acquisition control

1.

Press the foot control upward and keep it pressed.

Ä

A live video image appears with a green cross in the camera
view.

2.

Release the foot control.

Ä

The acquisition is automatically transferred to the 3D preview.

3.

Additional acquisitions can be created by repeating steps 1 and 2.

Ä

The model is restored automatically in the 3D preview during
the acquisition.

4.

Then check the above points once again. Take care that the optical
impression is sufficiently bright, sharp and free of motion blurring. If
you do not observe these points, one of them may have a negative
effect upon the subsequent procedure.

If you click the scan icon of the upper jaw, lower jaw or buccal
registration, you can take additional acquisitions of the upper jaw, lower
jaw or buccal registration.

«
...
46
47
48
49
50
...
»

Summary of Contents for cerec ac





















































































Reviews:

No comments

Related manuals for cerec ac

Brand: Cadex Pages: 5

Brand: Proseries Pages: 10

Advantage One 405

Brand: Team Orion Pages: 44

Brand: Prestigio Pages: 72

Brand: ALTEN Pages: 2

Brand: RIDGID Pages: 10

Brand: Vanner Pages: 12

Brand: Targus Pages: 26

Brand: AA Portable Power Corp Pages: 3

CoRe+ C+V1-PED-ADD

Brand: AddEnergie Pages: 13

Brand: NEC Pages: 71

Brand: ACDC Dynamics Pages: 4

Brand: ABB Pages: 117

Brand: Aegis Pages: 2

Brand: Aegis Pages: 2

Brand: DeWalt Pages: 56

Brand: FAR Pages: 24

Wireless Charging Pad

Brand: Samsung Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands