Sirona cerec ac Operating Instructions Manual Download Page 33

Page: 33 / 84

Sirona Dental Systems GmbH
Operating Instructions CEREC AC

6 Installation and startup

6.4 Initial startup

63 33 582 D3492
D3492.201.01.22.02 10.2018

6.4.5

Insert battery (optional)

Bottom door

Battery cover

Storage battery

Battery connector

Open the lower door on the back panel.

NOTE

Open with coin.

Use a coin to open the latch. Turn counterclockwise.

Remove the battery cover.

Insert the battery into the battery compartment with the mounting
screw and screw it down.

Plug in the battery plug.

Attach the battery cover.

Put the door back in position and lock it.

6.4.6

Using a trackball

Turn the collar (A) counterclockwise and remove it.

Insert the ball supplied.

Lay the collar (A) into position and turn it clockwise until it snaps
into place.

Summary of Contents for cerec ac





















































































Search results

Summary of Contents for cerec ac

Reviews:

Related manuals for cerec ac

Brands by name

Popular brands

Sirona cerec ac, Operating Instructions Manual

Search results

Summary of Contents for cerec ac

Reviews:

Related manuals for cerec ac

Brands by name

Popular brands