Sirona cerec ac Operating Instructions Manual Download Page 73

Page: 73 / 84

Sirona Dental Systems GmbH
Operating Instructions CEREC AC

10 Appendix

10.3 Seal on PC slide-in module

63 33 582 D3492
D3492.201.01.22.02 10.2018

10.3

Seal on PC slide-in module

NOTE

If the seal is broken, all warranty claims regarding the PC slide-
module automatically expire.

The PC slide-in module may be opened only by an authorized dental
technician. Only spare parts approved by us may be used in this
module.

Following a repair, the seal supplied along with the spare parts must be
affixed at the specified location (A).

10.4

PC Diagnostic Tool

10.4.1

Starting the diagnostic tool

Test

Suitable for

Customer Diagnostics

Suitable for the user, in order to
check the PC components.

Technician Diagnostics

Suitable for the technician, in order to
check the PC components.

Sirona Windows Diagnostics

Windows Stress Test, in order to test
the PC at permanent load.

Tip: If one of the following steps does not work, further steps can be
found in the Service Manual.

The PC is switched off.

Switch on the PC and wait until the above message appears.

Hold down the

"F11"

key on the keyboard until the boot menu

appears.

Summary of Contents for cerec ac





















































































Search results

Summary of Contents for cerec ac

Reviews:

Related manuals for cerec ac

Brands by name

Popular brands

Sirona cerec ac, Operating Instructions Manual

Search results

Summary of Contents for cerec ac

Reviews:

Related manuals for cerec ac

Brands by name

Popular brands