6
GB
o)
Battery chargers are for indoors use only.
Ensure that the power supply and charger
are protected against moisture at all times.
p)
NEVER start the power tool while the blade or accessory is in contact with the
workpiece, and always allow the power tool to reach its full speed before making
contact with the workpiece.
Use the variable speed control of the tool (if fitted) to start
the tool at the correct speed for the accessory or blade fitted.
q)
DO NOT exert additional pressure on the body of the tool: allow the blade or
accessory to do the work.
By not exerting additional pressure you maintain a safer
stronger grip on the power tool when it breaks through the material, as well as reducing
wear on the power tool which will extend the power tool’s service life. Additional
pressure may also bend or twist the accessory or blade which may cause it to break
and cause injury. If the power tool allows for being held with one or two hands hold with
two hands whenever possible. ALWAYS exercise caution when handling this power tool.
r)
Sawing, cutting and abrasive actions create heat.
This may affect the workpiece
and power tool. ALWAYS monitor the heat level and in the event of excessive heat
switch off the power tool and allow to cool before restarting work. Some power tools
depending on design may be more quickly and effectively cooled by running at high
speed without load.
s)
The power tool will draw in dust through the vents on its body.
Excessive
accumulation of powdered metal may cause an electrical hazard and destroy the tool.
ALWAYS ensure the environment dust level is safe for the tool and ensure the vents are
not blocked.
t)
For mains-operated power tools, ensure the cable of the power tool is ALWAYS
kept behind the tool and never close to where the accessory or blade is operating.
u)
DO NOT reach under the workpiece, rest the workpiece on your body, or hold the
workpiece while working on it, as contact with the blade or accessory protruding
from the workpiece can result in serious injury.
v)
Anti-vibration gloves should be worn when operating power tools that produce
large amount of vibration, especially during long-term use.
w)
For power tools with a rotating mechanism and accessories ensure the operator
is not wearing clothes or gloves with frayed threads, cords etc. that could be
entangled inthe rotating mechanism dragging the operator’s hand into the
rotating accessory causing injury.
ALWAYS wear tight fitting work clothes, safety
shoes. Remove jewellery and secure long hair. NEVER wear fabric-based gloves that can
produce strands of material when operating this type of power tool.
x)
DO NOT allow sanding sheets to wear away on the sanding pad.
This will damage
the surface of the pad requiring replacement and may cause parts of the sanding sheet
to fly off the pad, causing operator injury.
y)
DO NOT touch the moving sanding sheet.
z)
Wire brush bristles are thrown by the brush even during ordinary operation.
DO NOT overstress the wires by applying excessive load to the brush. The wire bristles
can easily penetrate light clothing and skin.
Note:
The tool must ONLY be used for its intended purpose. Any use other than those
mentioned in this manual will be considered a case of misuse. The operator, and not the
manufacturer, shall be liable for any damage or injury resulting from such cases of misuse.
The manufacturer shall not be liable for any modifications made to the tool, nor for any
damage resulting from such modifications.
Battery Charger Safety
Use the battery charger correctly.
• Refer to the section of this manual relating to use of the battery charger before
attempting to charge the battery
• DO NOT attempt to use the charger with any batteries other than those supplied. Keep
your battery charger clean; foreign objects or dirt may cause a short or block air vents.
Failure to follow these instructions may cause overheating or fire
• If the supply cord is damaged, it must be replaced by the manufacturer, the service
agent or similarly qualified persons in order to avoid a hazard
WARNING:
DO NOT attempt to recharge non-rechargeable batteries.
Battery Safety
WARNING:
Li-Ion batteries, if incorrectly used, stored, or charged are a fire, burn, and
explosion hazard.
• Keep the battery out of reach of children
• ONLY charge Li-Ion batteries using the charger provided or designed specifically for
your product
• ONLY use Li-Ion batteries provided with a product or specifically designed
to be compatible
• Allow batteries to cool for 15 minutes after charging or heavy use. Failure to follow
these instructions may cause overheating or fire
• When not in use batteries should be stored at room temperature (approximately 20°C)
• Ensure that battery contacts cannot accidentally short in storage. Keep batteries clean;
foreign objects or dirt may cause a short. Keep away from other metal objects, for
example paperclips, coins, keys, nails and screws
• Under abusive conditions, liquid may be ejected from the battery. This liquid may cause
skin irritation or burns. Avoid contact. If contact accidentally occurs, flush with water. If
liquid contacts eyes, seek medical help
• DO NOT open, disassemble, crush, heat above 60°C or incinerate. Do not dispose of in
fire or similar
Included accessories (not shown)
1 x Hex key
1 x Scraper Blade
1 x Saw Blade
4 x Sanding Sheets (2 x wood 80 and 120 grit; 2 x metal 80 and 120 grit)
Intended Use
Battery-operated multi-tool for light to medium duty cutting and abrasive tasks by fast
oscillation of a blade, file or sanding pad.
Unpacking Your Tool
• Carefully unpack and inspect your new multi-tool. Familiarise yourself with all its
features and functions
• Ensure that all parts of the tool are present and in good condition
• If any parts are missing or damaged, have such parts replaced before attempting to use
this tool
Before Use
IMPORTANT:
Your multi-tool’s battery comes partly charged. It is recommended that you
fully charge the battery before using the tool for the first time. It is also recommended that
you fully drain then fully charge the battery for a further 2 times to condition the battery,
ensuring optimal usage is achieved for the duration of the battery life.
Charging the Battery
WARNING:
ONLY use this charger to charge the supplied battery or additional
purchased batteries that are specifically designed for this tool.
WARNING:
The Battery Charger (13) is designed for indoor use only and MUST NOT
be used in damp or wet conditions.
WARNING:
Failure to follow the correct procedure when charging batteries will result
in permanent damage.
Note:
Fully charging the battery can take 3–5hrs, depending on how depleted the battery
charge is when inserting the battery into the charger. Also, it may take longer if the battery
has been in a discharged state for an extended period of time.
1. Plug the Mains Plug (14) into a mains socket
2. Insert the Battery (10) into the Battery Charger (13) (it can only fit in one way) and turn
the mains power on at the socket
3. The Red LED (16) will illuminate, which indicates charging
4. The Green LED (15) will illuminate once the Battery is fully charged
1
Blade
2
Accessory Mounting
3
On/Off Switch
4
Variable Speed Dial
5
Hand Grip
6
Battery
7
Battery Release
8
Motor Vents
9
Mounting Spindle
10 Mounting Washer
11 Mounting Bolt
12 Battery Charger
13 Mains Plug
14 Green LED
15 Red LED
16 Sanding Pad
Product Familiarisation
900798_Z1MANPRO1.indd 6
29/06/2016 09:40
