Silverline 129901, Manual

Page: 6 / 40

d) Use metal and voltage detectors to locate concealed electric,
water or gas lines. Avoid touching live components or conductors.
e) Extension cable reels used with this tool must be completely
unwound.
Minimum conductor cross section: 1.0mm 2 .
f) When using this tool outdoors, connect to a power supply with
an RCD device and minimum 1.5mm 2 extension cable with water
protected plugs in good working order.
g) Ensure that the chisel or drill bit is securely fixed in the chuck.
Insecure drill bits can be ejected from the machine causing a hazard.
h) Ensure that the lighting is adequate.
i) Ensure that the drill bit is in contact with the workpiece prior to
starting up the tool.
j) Before drilling, check that there is sufficient clearance for the drill
bit under the workpiece.
k) Use both hands when operating this tool. ALWAYS
use auxiliary
handles supplied with the tool.
l) DO NOT put pressure on the tool, to do so would shorten its service
life.
m) Drill bits get hot during operation, allow to cool prior to handling
them.
n) NEVER use your hands to remove sawdust, chips or waste close by
the bit.
o) If you are interrupted when operating the drill, complete the
process and switch off before looking up.
p) Where possible, use clamps or a vice to hold your work.
q) ALWAYS disconnect the hammer drill from the electric supply
before changing a chisel or drill bit.
r) Examine the chuck regularly for signs of wear or damage. Have
damaged parts repaired by a qualified service centre.
s) ALWAYS wait until the drill has come to a complete stop before
putting it down.
t) On completion of the work, disconnect the tool from the power
source and remove chisel/bit from the machine.
u) Periodically check all nuts, bolts and other fixings and tighten
where necessary.
Intended Use
Portable, mains-operated, general-purpose drill with hammer action,
suitable for light to medium duty drilling applications with wood, metal,
masonry and other materials.
6
GB
1 Chuck
2
Depth Stop Knob
3 Gear Selection Switch
4 Hammer Selection Switch
5 Forward/Reverse Selector
6 Lock On Button
7 Trigger Switch
8 Speed Control Dial
9
Fan Cooling Slots
10 Side Handle
11 Depth Stop Rod
Product Familiarisation
Unpacking Your Tool
• Carefully unpack and inspect your new sander. Familiarise yourself with
all its features and functions
• Ensure that all parts of the tool are present and in good condition. If
any parts are missing or damaged, have such parts replaced before
attempting to use this tool
Before Use
WARNING:
Ensure the tool is disconnected from the power supply
before attaching or changing any accessories, or making any adjustments.
Attaching the side handle
• The Side Handle (10) should always be used when drilling
• ALWAYS hold the drill firmly using both hands
• The Side Handle can be adjusted to best suit the work to be performed
• To adjust the Side Handle, rotate the handle grip anti-clockwise to loosen
the handle assembly. Move the Side Handle to the required position and
secure by rotating the handle grip clockwise
Operating the chuck
• The Chuck (1) can be opened by holding the rear chuck ring, and rotating
the front chuck ring anti-clockwise
• To tighten the chuck, hold the rear chuck ring, and rotate the front chuck
ring clockwise
• DO NOT run the drill to tighten or release the chuck. This will cause
permanent damage to your tool
Speed control
• The maximum speed of the drill can be limited by using the Speed
Control Dial (8). This limits the maximum settable speed of the Trigger
Switch (7) between 0 and 1000min
-1 (low gear), or 0 and 3000min -1
(high gear)
• Rotate Speed Control Dial (8) to adjust the speed as indicated on the
Trigger Switch
• Direction control
• The direction of the drill can be changed using the Forward/Reverse
Selector (5)
• To run the drill in a clockwise direction, push the Forward/Reverse
Selector to the right
• To run the drill in an anti-clockwise direction, push the Forward/Reverse
Selector to the left
• DO NOT attempt to move the Forward/Reverse Selector while the drill
is running
• DO NOT attempt to run the drill with the Forward/Reverse Selector in
mid-position
Hammer selection
• The drill can be used in either hammer drill mode (for masonry work) or
normal drill mode (for wood, metal etc)
• To select hammer drilling mode, Move the Hammer Selection Switch (4)
to the right
• To select rotary drilling mode, Move the Hammer Selection Switch to
the left
• DO NOT attempt to move the Hammer Selection Switch whilst the drill
is running
Gear selection
• The drill is equipped with 2 gears. This allows you to select the correct
gear to match the task to be performed. Low gear (0-1000min -1 ) is more
suitable for low speed tasks that require high torque including driving
screws and fasteners or drilling harder materials. High gear (0-3000min
-1
)
is more suitable for normal drilling. If the task to be performed does not
require speeds above 1000min
-1
, use the low gear, as this will reduce the
load on the motor
129901_Z1MANPRO1.indd 6 13/11/2015 15:54