Siemens SITRANS F FUE380 Operating Instructions Manual Download Page 36

Page: 36 / 102

NOTICE
Verification sealing
For SITRANS FUE380 systems, the cable length setting is protected by a verification sealing.

The verification sealing must only be broken by the user with the acceptance of the local

authorities.

Connecting transducer cables
1. Wiring the transducer cables.

The system SITRANS FUE380/FUS380 transmitter is supplied with 4 separate transducer

coaxial cables for 2 paths.

The cables can be used on all transducers, but can be marked for a specific transducer

(cables are not paired with a specific transducer). The cables are manufactured with crimp

on the cable ends for the connection board.

Connect each transducer cable to the sensor. Tighten the transducer cable glands to ensure

they are firmly sealed! Recommended torque for each sensor gland is approx. 20 Nm.

nnm

nmn

2. Snap out the connection plate and loosen the grounding wire.

Connecting
5.3 Remote system

FUS380/FUE380

Operating Instructions, 09/2016, A5E00730100-AB

Summary of Contents for SITRANS F FUE380







































































































Search results

Summary of Contents for SITRANS F FUE380

Reviews:

Siemens SITRANS F FUE380, Operating Instructions Manual, Page: 36 / 102

Search results

Summary of Contents for SITRANS F FUE380

Reviews: