manualshive.com logo in svg

Siemens SITRANS F FUE380, Operating Instructions Manual, Page: 32 / 102

Share
Download
Siemens SITRANS F FUE380 Operating Instructions Manual Download Page 32

5.2

Compact system

Connect the compact flowmeter using the following steps.

Connecting battery (battery-powered versions and mains-powered versions with back-up battery)

Plug in male battery plug. Ensure that the wire is inserted into the small channel leading from 

plug to battery.

Preparing connection

Remove protection cover carton from the terminal box.

Connecting power supply cable (mains-powered versions only)

WARNING

Power supply requirements
Make sure the power supply requirements stated on the nameplates are met!

WARNING

Wire insulation   
The insulation between the connected mains supply and the low voltage supply for the 

flowmeter must be rated with at least double or reinforced insulation at mains voltage.
For field wiring installation: Ensure that the National Installation Code of the country in which 

the flowmeters are installed is met.

Note
Conductor terminal     
The wire size for the output terminals are AGW24 to AGW14 or 0.205 mm

2

 to 2.080 mm

2

.

Connecting
5.2 Compact system

FUS380/FUE380

32

Operating Instructions, 09/2016, A5E00730100-AB

Summary of Contents for SITRANS F FUE380







































































































Reviews:

No comments