Siemens SITRANS F FUE380 Operating Instructions Manual Download Page 14 | Manualshive

Page: 14 / 102

Siemens SITRANS F FUE380 Operating Instructions Manual Download Page 14

Instrument safety standards

The device has been tested at the factory, based on the safety requirements. In order to

maintain this condition over the expected life of the device the requirements described in these

Operating Instructions must be observed.

NOTICE
Material compatibility
Siemens Flow Instruments can provide assistance with the selection of wetted sensor parts.

However, the full responsibility for the selection rests with the customer and Siemens Flow

Instruments can take no responsibility for any failure due to material incompatibility.

CE-marked equipment

The CE mark symbolizes the compliance of the device with the following directives:
● EMC-directive 2004/108/EC
● Low voltage directive 2006/95/EC
● Pressure equipment directive (PED/DGRL) 93/23/EC
● ATEX Directive 94/9/EG

2.4

Installation in hazardous area

WARNING

NOT allowed for use in hazardous areas!
Equipment used in hazardous areas must be Ex-approved and marked accordingly!
This device is NOT approved for use in hazardous areas!

WARNING

500 V insulation test
The device is not capable of withstanding the 500 V insulation test required by Clause 6.3.12

of EN60079-11. This must be taken into account when installing the device.

2.5

Certificates

You can find certificates on the Internet at online support portal (

http://www.siemens.com/

processinstrumentation/certificates

) or on an included DVD.

Safety notes
2.5 Certificates

FUS380/FUE380

14

Operating Instructions, 09/2016, A5E00730100-AB

«
...
12
13
14
15
16
...
»

Summary of Contents for SITRANS F FUE380







































































































Reviews:

No comments