Siemens SINAMICS G110 Operating Instructions Manual Download Page 4 | Manualshive

Page: 4 / 92

background image

SINAMICS G110 Operating Instructions

4

6SL3298-0AA11-0BP0

Summary of Amendments

Edition Valid

for

firmware
version

Status/Changes

Order no of the inverter

6SL3211-0xxxx-xxxx

04/2003 1.0

First

issue

Last digit “0”

6SL3211-0xxxx-xxx

0

11/2004 1.0

1.1

New features inserted:

Types of Control using the Terminals (2 wire/3 wire control)

4.3.4 Parameter P1234 in DC braking

4.3.5 Compound braking

Last digit “0”

6SL3211-0xxxx-xxx

0

Last digit “1”

6SL3211-0xxxx-xxx

1

04/2005

6.1 Troubleshooting with Standard Inverter LED - timings of
LED has been updated.

Approved Siemens Quality for Software and Training
is to DIN ISO 14001, Reg. No. 2160-01

The reproduction, transmission or use of this document, or
its contents is not permitted unless authorized in writing.
Offenders will be liable for damages. All rights including
rights created by patent grant or registration of a utility
model or design are reserved.

© Siemens AG 2005. All Rights Reserved.

SINAMICS® is a registered trademark of Siemens.

Other functions not described in this document may be
available. However, this fact shall not constitute an
obligation to supply such functions with a new control, or
when servicing.

We have checked that the contents of this document
correspond to the hardware and software described.
There may be discrepancies nevertheless, and no
guarantee can be given that they are completely
identical. The information contained in this document is
reviewed regularly and any necessary changes will be
included in the next edition. We welcome suggestions for
improvement.

Siemens handbooks are printed on chlorine-free paper
that has been produced from managed sustainable
forests. No solvents have been used in the printing or
binding process.

Document subject to change without prior notice.

Order Number. 6SL3298-0AA11-0BP0
Printed on demand in Fürth, Germany

Siemens-Aktiengesellschaft.

«
...
2
3
4
5
6
...
»

Summary of Contents for SINAMICS G110





























































































Reviews:

No comments

Related manuals for SINAMICS G110

Clavinova CLP-240

Brand: Yamaha Pages: 24

GA700 GA700 Series

Brand: YASKAWA Pages: 32

Brand: Siemens Pages: 258

Brand: SHS Pages: 29

Brand: SHS Pages: 33

XtraDrive Series

Brand: YASKAWA Pages: 96

SGD7S 020 Series

Brand: YASKAWA Pages: 111

CACR-SR BB1 Series

Brand: YASKAWA Pages: 81

Planetgear 7000

Brand: Rexnord Pages: 33

Brand: Black Box Pages: 2

DL DVD RW Drive

Brand: LaCie Pages: 41

Atrium HS Comfort drive

Brand: Maco Pages: 64

Brand: YASKAWA Pages: 1016

Brand: ICAN Pages: 16

Brand: Moons' Pages: 48

Brand: YASKAWA Pages: 12

Brand: Lenze AC Tech Pages: 33

EMME-AS-40-S Series

Brand: Festo Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands