Siemens SIMOMED HM Service Instructions Manual Download Page 11 | Manualshive

Page: 11 / 24

background image

Siemens AG

RA52-060.061.01.07.02

SIMOMED HM

07.02

TD SD 21

Replacing the Firmware

11

Page 11 of 24

Medical Solutions

5-

4Replacing the Firmware

FW Replacement

0

NOTE

Insert the screw inserted in plastic as follows:

Turn the screw counterclockwise until it snaps in place, only then
turn it clockwise to tighten it.

•

Unplug the power connector.

•

The FW is located on the digital controller.

•

The digital controller is located behind the
front control panel.

•

Unlatch the front control panel (on both
sides) using the unlatching tool that is includ-
ed in the shipment, and flip it down.

•

Disconnect the ribbon cable from the digital
controller to the monitor.

•

Remove the metal shielding (2 screws).

•

Replace the FW.

•

Installation

is in the reverse order of the

steps above.

Fig. 1:

«
...
9
10
11
12
13
...
»

Summary of Contents for SIMOMED HM

























Reviews:

No comments

Related manuals for SIMOMED HM

Brand: Hanns.G Pages: 18

Brand: Wahoo Pages: 5

Brand: iHealth Pages: 14

Brand: Hanns.G Pages: 20

HD 08T21 STD-xxx-F Series

Brand: Hatteland Pages: 40

Brand: V7 Pages: 1

Brand: Badger Meter Pages: 4

Brand: Melissa Pages: 51

Brand: BAFANG Pages: 20

Brand: Ametek Pages: 46

Brand: Parker Pages: 52

Brand: Symphony Pages: 9

Brand: B.Well Pages: 72

EAGLE EAGLE 920HRM

Brand: Accusplit Pages: 18

Brand: boso Pages: 158

Brand: Fujitsu Pages: 25

Brand: Fujitsu Pages: 2

MCM1514V D556Q 154V/C551

Brand: Fujitsu Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands