Siemens SIMOMED HM Service Instructions Manual Download Page 6

Page: 6 / 24

General Remarks

SIMOMED HM

RA52-060.061.01.07.02

Siemens AG

07.02

TD SD 21

Page 6 of 24

Medical Solutions

Troubleshooting / Repair / Replacement

Beginning / since February 2001, the monitor is only replaced completely when there is a
malfunction.

•

Every defective monitor must be returned with an exact description of the malfunction!

•

Without a description of the malfunction, sporadic and/or temperature-related effects or
even system-dependent causes almost never can be found.

NOTE

If a middle monitor in an MTS 1 / 3 / 6 needs to be replaced, the po-
sition of the monitor to the rear longitudinal strut can be changed
so that the monitor can be replaced without “spending extra time”
on it.

However, the document

for MTS 1/3/6

(AX52-X01.812.01 / Transverse Strut Horizontal Rota-

tion at the Bottom)

for MTS 6, upper traverse

(AX52-X01.812.01 / Turning the Top Hor-

izontal Transverse Strut)

must be observed!

WARNING

Increased risk of injury!

If the installation document is not observed, the traverse can fall
and crushing can occur.

Installation Instructions, AX52-X01.812.01.... absolutely
must be observed.

Test Equipment and Aids

•

Laptop with the Windows operating system.

•

Serial interface cable (0 modem cable).

See CB - DOC TD00-000.801.01.... (Spare Parts Catalogue),
Part No. 99 00 440 RE999.

NOTE

A gender changer is no longer needed.

•

Monitor Multinorm Testbox.

See CB - DOC TD00-000.801.01.... (Spare Parts Catalogue)
Part No. 97 16 754 Y4905

•

Set of Torx offset screwdrivers.

See CB - DOC TD00-000.801.01.... (Spare Parts Catalogue)
Part No. 99 00 663 GE999

Summary of Contents for SIMOMED HM

























Search results

Summary of Contents for SIMOMED HM

Reviews:

Related manuals for SIMOMED HM

Brands by name

Popular brands

Siemens SIMOMED HM, Service Instructions Manual

Search results

Summary of Contents for SIMOMED HM

Reviews:

Related manuals for SIMOMED HM

Brands by name

Popular brands