Siemens SIMATIC RF120C Operating Instructions Manual Download

Page: 25 / 92

Parameter assignment and configuration

4.3 Parameter assignment with the device configuration

Communications module RF120C with application blocks for S7-1200 and S7-1500
Operating Instructions, 07/2013, C79000-G8976-C328-01

4.3.2.2

RF300

Table 4- 4

RF300 general

Parameter

Parameter value

Default value

Description

Transponder type

RF300
ISO 15693

RF300

Selection of the transponders used.

Table 4- 5

RF380R

Parameter

Parameter value

Default value

Description

RF power

0.50 - 2.00 W

1.25 W

Setting for the output power of the reader.

Transponder type

RF300
ISO 15693

RF300

Selection of the transponders used.

4.3.2.3

RF600

Table 4- 6

RF600 general

Parameter

Parameter value

Default value

Description

Max. no. of transponders

1 - 80

Number of transponders expected in the

antenna field.
Permitted values:

•

1 - 40 for RF620R

•

1 - 80 for RF630R with 2 antennas

•

1 - 40 for RF630R with 1 antenna

The value stored in "multitag" defines the

expected number of transponders to be read

(EPC-ID) in the inventory.

The value does not restrict the number of

transponders to be processed in the antenna

field.

To ensure an efficient inventory of

transponders in the antenna field, make sure

that the values specified here do not deviate

by more than approximately 10% from the

maximum number of transponders to be

expected in the antenna field.

Reader type

RF620R ETSI
RF620R FCC
RF620R CMIIT
RF630R ETSI
RF630R FCC
RF630R CMIIT

RF620R ETSI

Selection of the reader used.
By selecting a reader, you open the "Reader

type" menu. This menu is described in the

following section.

Summary of Contents for SIMATIC RF120C





























































































Search results

Summary of Contents for SIMATIC RF120C

Reviews:

Related manuals for SIMATIC RF120C

Brands by name

Popular brands

Siemens SIMATIC RF120C, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC RF120C

Reviews:

Related manuals for SIMATIC RF120C

Brands by name

Popular brands