Siemens SIMATIC RF120C Operating Instructions Manual Download

Page: 23 / 92

Parameter assignment and configuration

4.3 Parameter assignment with the device configuration

Communications module RF120C with application blocks for S7-1200 and S7-1500
Operating Instructions, 07/2013, C79000-G8976-C328-01

Submenu: Diagnostics
Parameter assignment options:

●

None
Apart from standard diagnostics, no other alarms are generated.

●

Hard errors
Extended alarms are generated if the following events occur.
–

Hardware fault (memory test)

–

Firmware error (checksum)

–

Connection to reader lost

–

Short-circuit fault/interruption if supported by the hardware

You will find more detailed information on diagnostics in the section "Diagnostics (Page 49)".

4.3.2

Menu: Reader System

In this menu you can set all specific parameters for the selected RFID system.

Figure 4-3

General parameter assignment options of the RF300 reader system

Summary of Contents for SIMATIC RF120C





























































































Search results

Summary of Contents for SIMATIC RF120C

Reviews:

Related manuals for SIMATIC RF120C

Brands by name

Popular brands

Siemens SIMATIC RF120C, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC RF120C

Reviews:

Related manuals for SIMATIC RF120C

Brands by name

Popular brands