Siemens SIMATIC RF120C Operating Instructions Manual Download Page 10

Page: 10 / 92

Description

2.3 Integration

Communications module RF120C with application blocks for S7-1200 and S7-1500

Operating Instructions, 07/2013, C79000-G8976-C328-01

Configuration

The following figure shows the SIMATIC S7-1200 with three RF120C communications

modules.

Figure 2-3

Maximum configuration of RF120C with a SIMATIC S7-1200

Extensive configurations are possible using a PROFIBUS/PROFINET setup with various

SIMATIC Ident communications modules.

2.3

Integration

The figure below shows how the SIMATIC S7-1200 with SIMATIC RF120C is integrated into

an automation system.

Figure 2-4

Example of integrating a SIMATIC S7-1200 with RF120C

The RF120C is integrated in the SIMATIC S7-1200 hardware configuration using an HSP.

Following this, the RF120C can be configured in the TIA Portal using the device

configuration. You will find the HSP on the DVD "RFID Systems, Software & Documentation"

or on the Internet on the Support homepage

(

http://support.automation.siemens.com/WW/view/en/23183356

Summary of Contents for SIMATIC RF120C





























































































Search results

Summary of Contents for SIMATIC RF120C

Reviews:

Related manuals for SIMATIC RF120C

Brands by name

Popular brands

Siemens SIMATIC RF120C, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC RF120C

Reviews:

Related manuals for SIMATIC RF120C

Brands by name

Popular brands