Siemens SIMATIC RF120C Operating Instructions Manual Download Page 52

Page: 52 / 92

Service and maintenance

5.3 FB error messages

Communications module RF120C with application blocks for S7-1200 and S7-1500

Operating Instructions, 07/2013, C79000-G8976-C328-01

5.3.2

Error messages

Errors from the communications module/reader

The causes of these errors can, for example, be as follows:

●

Errors have occurred in communication between the CM and the reader or between the

reader and the transponder.

●

The communications module is unable to process the command.

Byte 3 of the STATUS is not relevant for the error messages.
With certain error messages of the communications module, the ERR-LED also flashes (see

the two tables below).

Table 5- 3

Evaluation of the ERR LED

Flashing of

ERR LED

Error in

STATUS

Errors that have occurred

E4 FE 07

No error

Communications module has started up and is waiting for an "init_run"

E4 FE 03

Error in the connection to the reader; the reader is not answering

E6 FE 01

unknown command (all product families);

incorrect parameter assignment (RF600 only)

17x

E4 FE 01

Short-circuit or overload

18x

E4 FE 8D Internal communication error of the communications module

19x

E4 FE 04

The reader does not have enough buffer on the communications

module to store the command temporarily.

20x

E4 FE 8D Internal monitoring error of the communications module

21x

E4 FE 15

Incorrect parameter assignment of the communications module

23x

E4 FE 8C

E5 FE 01

E5 FE 04

Communication error between Ident profile and communications

module. Handshake error.

25x

E5 FE 08

An error has occurrerd that makes a WRITE-CONFIG with Config = 3

necessary.

30x

E5 FE 06

E6 FE 02

E6 FE 0

Error when processing the command

Summary of Contents for SIMATIC RF120C





























































































Search results

Summary of Contents for SIMATIC RF120C

Reviews:

Related manuals for SIMATIC RF120C

Brands by name

Popular brands

Siemens SIMATIC RF120C, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC RF120C

Reviews:

Related manuals for SIMATIC RF120C

Brands by name

Popular brands