Siemens Simatic PG 740 PIII Operating Instructions Manual Download Page 68

Page: 68 / 70

Hotline Services

8-2

Operating Instructions PG 740 PIII

A5E00063150-03

8.2

SIMATIC Customer Support Online Services

The SIMATIC Customer Support team offers you substantial additional information
about SIMATIC products via its online services:

General current information can be obtained from:

– the Internet under

http://www.ad.siemens.de/simatic

Current product information leaflets and downloads which you may find useful
are available:

– the Internet under

http://www.ad.siemens.de/simatic-cs

– via the Bulletin Board System (BBS) in Nuremberg (SIMATIC Customer

Support Mailbox) under the 49 (911) 895-7100.

To access the mailbox, use a modem with up to V.34 (28.8 Kbps) with
parameters set as follows: 8, N, 1, ANSI; or dial in via ISDN (x.75, 64 Kbps).

You can find your local customer service representative for Automation & Drives
in our customer service representative data bank:

– in the Internet under

http://www3.ad.siemens.de/partner/

search.asp?lang=en

Summary of Contents for Simatic PG 740 PIII







































































Search results

Summary of Contents for Simatic PG 740 PIII

Reviews:

Brands by name

Popular brands

Siemens Simatic PG 740 PIII, Operating Instructions Manual

Search results

Summary of Contents for Simatic PG 740 PIII

Reviews:

Brands by name

Popular brands