manualshive.com logo in svg

Siemens Simatic PG 740 PIII, Operating Instructions Manual

Share
Download
Siemens Simatic PG 740 PIII Operating Instructions Manual Download Page 56

Reinstallation of the Software

6-12

Operating Instructions PG 740 PIII

A5E00063150-03

f the network settings are not correct, you can change them via Control panel >
Network.

Note

When prompted to insert the data carrier labelled Intel PRO Adapter, insert the
Backup CD in the CD drive and type the path
\Drivers\PG740P3\Network\IntE100B for the source.

6.5

Installing the Operating System Windows 2000

Do not follow these instructions unless you want to upgrade from Windows 98 to
Windows 2000 or if you want to install Windows NT.

The new installation or reinstallation of the operating system is accomplished with
the ”Recovery Microsoft Windows 2000” CD-ROM.

This CD contains encoded files which can only be transferred to a SIEMENS
SIMATIC programming device.

The transfer of information is made with the program OEMSETUP.EXE on the
CD-ROM, or after booting from the CD-ROM with the recovery function.

The folders BOOTDISK, DISCOVER, SETUPTXT, SUPPORT and VALUEADD on
the CD ”Recovery Microsoft Windows 2000” are not encoded. These programs,
texts and functions can always be executed directly from the CD.

The installation of the operating system via the Windows 2000 setup program is
possible after transferring the necessary data to the hard disk. The Windows 2000
setup starts when you enter
HD:\>I386\WINNT.EXE. 
(HD: drive on which the folder I368 was transferred to).

Setup for Windows 2000 can be carried out for existing Windows installations via
the program HD:\I386\WINNT32.EXE.

Summary of Contents for Simatic PG 740 PIII







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands