manualshive.com logo in svg

Siemens Simatic PG 740 PIII, Operating Instructions Manual

Share
Download
Siemens Simatic PG 740 PIII Operating Instructions Manual Download Page 31

Hardware Components of the PG 740 PIII

3-9

Operating Instructions PG 740 PIII
A5E00063150-03

Note

In order to achieve a reliable operation and high data security, please note the fol-
lowing during use:

S

Store and transport the Superdisk in the protective cassette included. Doing
this will keep dust and dirt from the disk.

S

Remove Superdisk from the drive when it is not being read or written to keep
dirt particles away from the disk. Do not expose the disk to unnecessarily high
operating temperatures.

A Superdisk can be completely read or written in 15 minutes.

Note

If possible avoid vibration of the device, when using Superdisks. Superdisks are
more sensitive to vibration as a result of their high track density.

Emergency removal:
By inserting a pen (or a paper clip) while the device is switched off, you can force
the disk out of the drive.

Recommended Superdisks:

The Superdisks available commercially vary in quality. The best results in our quali-
fication tests achieved the third generation disks from the company IMATION.

External identification features: blue housing and silver-colored sliding cover.

These Superdisks can be obtained from the following addres.

IMATION corp.

IMATION Europe BV

IMATION Deutschland GmbH

1 Imation Place

1119 PH Schipol-RIJK

Hammfelddamm 11

Oakdale, MN 55128-3414

41460 Neuss

USA

Netherland

Germany

Phone (888) 466-3456

Tel  +31 (0) 20 654 2100

Tel  +49 (0) 2131 226 01

E-mail  [email protected]

Fax  +31 (0) 20 654 2222

Fax  +49 (0) 2131 226 100

Siemens Drives & PLCs

Summary of Contents for Simatic PG 740 PIII







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands