Siemens Simatic PG 740 PIII Operating Instructions Manual Download Page 20 | Manualshive

Page: 20 / 70

background image

Starting up and Operating the PG

2-4

Operating Instructions PG 740 PIII

A5E00063150-03

2.3

Operating the PG 740 PIII

Connecting to the Power Supply

You can operate the PG 740 PIII on 115 V and 230 V power systems. The voltage
is selected automatically.

1. Plug the power supply cable supplied with the unit into the connector labeled

”Power”.

2. Connect the unit to a socket outlet with grounded protective conductor.

Power supply
connector socket

Figure 2-1 Connecting the Power Supply

Note

The power plug must be disconnected to isolate the unit completely from the
supply.

Note

For operation in Canada and the US, a CSA or UL listed power supply cable must
be used.

The unit is intended for operation with normal grounded power supply networks
(TN networks, VDE 0100 part 300 or IEC 364-3).

The unit is not intended for operation with non-grounded or impedance-grounded
systems (IT systems).

«
...
18
19
20
21
22
...
»

Summary of Contents for Simatic PG 740 PIII







































































Reviews:

No comments

Related manuals for Simatic PG 740 PIII

Brand: Yanmar Pages: 44

Brand: MSI Pages: 92

phyBOARD-Subra-i.MX6

Brand: Phytec Pages: 2

Brand: Aaeon Pages: 119

Brand: ASROCK Pages: 64

Brand: Biostar Pages: 31

Brand: ECS Pages: 82

Brand: JETWAY Pages: 44

Brand: MSI Pages: 92

AnadigmApex AN231K04-DVLP3

Brand: Anadigm Pages: 16

Brand: Linear Pages: 6

Brand: Microsemi Pages: 22

Brand: Arbor Technology Pages: 68

Brand: PC Partner Pages: 20

Brand: Gigabyte Pages: 88

Brand: JETWAY Pages: 46

Brand: Gigabyte Pages: 34

P5B PRO - QUICK

Brand: ASROCK Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands