Siemens Simatic PG 740 PIII Operating Instructions Manual Download Page 29

Page: 29 / 70

Hardware Components of the PG 740 PIII

3-7

Operating Instructions PG 740 PIII
A5E00063150-03

3.6

Drives

The PG 740 PIII is standardly equipped with a LS120 drive, a 3.5 in. hard disk
drive and a CD-ROM drive.

Hard Disk Drive

Whenever the hard disk is accessed, the access LED on the front of the unit lights
up.

Caution

Risk of loss of data and damage to the drive!

Drives are sensitive to vibrations and shock. Any vibrations occurring during
operation can lead to the loss of data or damage to the drive.

If you intend transporting the unit, switch it off, and wait until the drive has come to
rest (about 20 seconds) before you move it.

LS120 Drive

The LS120 drive is compatible with previous 3.5”-disk drives. It also offers the
possibility of using storage media with a capacity of 120 Mbytes. With the LS120
drive, you can save programs and data on diskettes and load data to the
PG 740 PIII.

Types of Diskette

You can use the following diskettes:

LS120 SuperDISK

double sided

high density diskette

double sided

double density diskette

3.5 in.

120 Mbyte

1.44 Mbyte (135 TPI)

720 Kbyte

The PC recognizes the disk type by the coding. Superdisks can only be used in a
LS120 drive.

Siemens Drives & PLCs

Summary of Contents for Simatic PG 740 PIII







































































Search results

Summary of Contents for Simatic PG 740 PIII

Reviews:

Related manuals for Simatic PG 740 PIII

Brands by name

Popular brands

Siemens Simatic PG 740 PIII, Operating Instructions Manual

Search results

Summary of Contents for Simatic PG 740 PIII

Reviews:

Related manuals for Simatic PG 740 PIII

Brands by name

Popular brands