Siemens Simatic PG 740 PIII Operating Instructions Manual Download Page 53

Page: 53 / 70

Reinstallation of the Software

6-9

Operating Instructions PG 740 PIII
A5E00063150-03

Sound Driver Installation after Installing Windows

This chapter describes how to install sound drivers after having installed
Windows 98.

Please observe the following instructions to install the sound drivers located in
the directory

C:\DRIVERS\AUDIO.W98 or located in the directory
DRIVERS\PG740P3\AUDIO.W98 of the supplied CD “Backup PG720/740”.

Please read the file Readme.txt before you start installation.

Click “Start”, then “Settings” “Control Panel” and double-click “Add New
Hardware”.

Click “Next”, “Next” in Add New Hardware Wizard .

Select “No, I want to select the hardware from a list” and press “Next”.

Click “Sound, Video and Game controller” and press “Next“.

Click “Have Disk”.

At the command prompt “Copy manufacturer’s files from” type :

\DRIVERS\PG740P3\ AUDIO.W98 on the CD “Backup PG720/740”, select the
file “oemsetup.inf” and confirm with “OK”.

Press “Finish”.

Windows 98 updates the system settings and asks you to restart the PG for these
new settings to take effect. Confirm with “Yes”.

Installing Display Drivers

During setup Windows 98 detects the display device installed. If Windows 98 does
not recognize the existing driver for this device, proceed as follows:

Insert the “Backup PG720/740” CD in the CD-ROM drive

At the command promt

copy manufacturer’s files from

type
\DRIVERS\PG740P3\DISPLAY.W98

and press “OK”. The recognized display device is displayed.

Confirm with “Finish”.

Siemens Drives & PLCs

Summary of Contents for Simatic PG 740 PIII







































































Search results

Summary of Contents for Simatic PG 740 PIII

Reviews:

Related manuals for Simatic PG 740 PIII

Brands by name

Popular brands

Siemens Simatic PG 740 PIII, Operating Instructions Manual

Search results

Summary of Contents for Simatic PG 740 PIII

Reviews:

Related manuals for Simatic PG 740 PIII

Brands by name

Popular brands