background image

 

SIMATIC IPC627E 
Operating Instructions, 12/2018, A5E44297201-AA 

5

 

Table of contents 

 

 
 

Preface ...................................................................................................................................................... 3 

Product description .................................................................................................................................. 11 
1.1 

Important instructions and manuals for operating the device ................................................. 11 

1.2 

Product highlights ................................................................................................................... 13 

1.3 

Applications ............................................................................................................................. 15 

1.4 

External design of the device .................................................................................................. 16 

1.4.1 

Front panel .............................................................................................................................. 16 

1.4.2 

Rear of the device ................................................................................................................... 20 

1.4.3 

Status displays ........................................................................................................................ 21 

1.5 

Internal design of the device ................................................................................................... 23 

1.6 

Accessories and spare parts .................................................................................................. 24 

1.6.1 

Accessories: Hardware ........................................................................................................... 24 

1.6.2 

Accessories: Software ............................................................................................................ 25 

Safety instructions ................................................................................................................................... 27 
2.1 

General safety instructions ..................................................................................................... 27 

2.2 

Note on transport and storage ................................................................................................ 29 

2.3 

Notes on mounting .................................................................................................................. 30 

2.4 

Notes on ambient and environmental conditions .................................................................... 30 

2.5 

Information on I/O devices ...................................................................................................... 33 

2.6 

Notes on device and system extensions ................................................................................ 34 

Installing and connecting the device ........................................................................................................ 35 
3.1 

Preparing for installation ......................................................................................................... 35 

3.1.1 

Scope of delivery .................................................................................................................... 35 

3.1.2 

Checking the delivery package ............................................................................................... 37 

3.1.3 

Identification data of the device .............................................................................................. 38 

3.2 

Installing the device ................................................................................................................ 39 

3.2.1 

Installation guidelines ............................................................................................................. 39 

3.2.2 

Mounting positions .................................................................................................................. 41 

3.2.3 

Installation of the device with wall mounting rails ................................................................... 42 

3.2.4 

Installing the device with the vertical mounting kit .................................................................. 43 

3.2.5 

Installing the device with the vertical mounting kit for PC port access from the front ............ 44 

3.3 

Connecting the device ............................................................................................................ 45 

3.3.1 

Country-specific information on supply voltage ...................................................................... 45 

3.3.2 

Connection of equipotential-bonding cable ............................................................................ 46 

Summary of Contents for SIMATIC IPC627E





































































































































































Reviews: