Siemens SIMATIC IPC627E Operating Instructions Manual Download

Page: 43 / 164

Installing and connecting the device

3.2 Installing the device

SIMATIC IPC627E
Operating Instructions, 12/2018, A5E44297201-AA

3.2.4

Installing the device with the vertical mounting kit

The optional vertical mounting kit allows space-saving installation of the device.

Note
See the notes under "Mounting positions (Page 41)".

Securing the vertical mounting plate to the device

Remove the equipotential bonding screw

①

from the device and attach it to the vertical

mounting plate

②

Secure the vertical mounting plate to the device using the following number of screws:
–

SIMATIC IPC627E: Four or 7 M4 screws; torque 3 Nm

①

Remove the screw and the toothed lock washer and fasten them again after installing the vertical mounting plate.

②

Remove the screw prior to mounting.

Summary of Contents for SIMATIC IPC627E





































































































































































Search results

Summary of Contents for SIMATIC IPC627E

Reviews:

Related manuals for SIMATIC IPC627E

Brands by name

Popular brands

Siemens SIMATIC IPC627E, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC IPC627E

Reviews:

Related manuals for SIMATIC IPC627E

Brands by name

Popular brands