Siemens SIMATIC IPC627E Operating Instructions Manual Download

Page: 74 / 164

Expanding and assigning parameters to the device

6.2 Expansion cards

SIMATIC IPC627E

Operating Instructions, 12/2018, A5E44297201-AA

6.2.2

Installing/removing expansion cards

Note
Requirement for expansion cards
You can find the permitted dimensions for expansion cards under "Dimension drawing of the

expansion cards (Page 129)". If the permissible height is exceeded, contact problems,

malfunctions and installation difficulties cannot be ruled out.

Requirements

●

The device is open (see: Opening the Device (Page 71)).

Procedure - Installation

NOTICE
Damage to the expansion card.
The expansion card can break if excessive force is used.

•

Do not apply any pressure.

•

Do not apply excessive force on the slider when you push it onto the expansion card.

Remove the marked screw

①

and swivel the cover to the side as shown. Then remove

the marked screws and the panels.

Summary of Contents for SIMATIC IPC627E





































































































































































Search results

Summary of Contents for SIMATIC IPC627E

Reviews:

Related manuals for SIMATIC IPC627E

Brands by name

Popular brands

Siemens SIMATIC IPC627E, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC IPC627E

Reviews:

Related manuals for SIMATIC IPC627E

Brands by name

Popular brands