Siemens SIMATIC IPC627E Operating Instructions Manual Download

Page: 51 / 164

Installing and connecting the device

3.3 Connecting the device

SIMATIC IPC627E
Operating Instructions, 12/2018, A5E44297201-AA

3.3.4

Connecting I/O devices

CAUTION

Fault caused by I/O devices
The improper connection of I/O devices can cause faults in the device.
The result may be personal injury and damage to the machine or plant.

•

You should observe the warnings relating to the connection of I/O devices in

"Information on I/O devices (Page 33)".

Procedure

Note
Use the original connections of the I/O to be connected without adapters or extensions.

Connect the I/O devices to the respective interfaces.
Information on the position of the interfaces is available in "Front panel (Page 16)".

Secure the cables with the strain relief.
See: Connecting Ethernet/USB strain relief (Page 54)

Summary of Contents for SIMATIC IPC627E





































































































































































Search results

Summary of Contents for SIMATIC IPC627E

Reviews:

Related manuals for SIMATIC IPC627E

Brands by name

Popular brands

Siemens SIMATIC IPC627E, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC IPC627E

Reviews:

Related manuals for SIMATIC IPC627E

Brands by name

Popular brands